1)  attitude mode
姿态模型
1.
Then through dealing with above equations, the attitude model of under actuated sub-mini unmanned rotorcraft, which contained input variable, output variable and some unknown parameters, was set up.
采用机理分析和系统辨识相结合的方法,以直升机机体和伺服小翼的力矩平衡方程为基础,根据滞空状态的特性,建立含有未知参数的超小型旋翼无人机姿态模型,由飞行数据采用预测误差法(PEM)对上述姿态模型进行了辨识,从而得到了完整的滞空状态下超小型旋翼机系统的姿态模型,最后验证了辨识模型的正确性。
2)  Generalized attitude models
广义姿态模型
3)  the Satellite Orbit Attitude Model
轨道姿态模型
1.
In this thesis the systematic research of geometrical model has been carried out on the Satellite Orbit Attitude Model, the Rational Function Model, and the Differential Polynomial Model.
本文对高分辨率卫星影像的成像几何模型进行了比较系统的研究,分别论述了卫星轨道姿态模型、有理函数模型和微分多项式模型,建立了具体的模型定向实现算法,在此基础上开发了微机版的影像正射纠正软件,最后详细描述了利用三种模型进行的大量实验及结果分析。
4)  posture
姿态
1.
The paper analyses the relation between hydraulic support posture and wall rock destruction, and propose the monitoring methods of hydraulic support posture.
分析了液压支架姿态与围岩破坏的关系,提出液压支架姿态的监测方法和手段,结合现场实际,确定出液压支架姿态控制的合理范围。
2.
An implementation principle using this me-chanism design is demonstrated by which the chassis centerline can approach the leading line gradually through continuously adjusting the chassis posture.
论证了在这种机构设计下通过不断调整底盘姿态的方法可以让底盘中心线逐渐与引导线重合的实现原理。
3.
By means of the authentic proof study and analysis on the sensitivities of the spatial position and posture of output spindle affected by 6 linear inputted kinematic parameters,different key effects made by the inputted kinematic parameters of the upper and lower level of moving platforms of the mechanism .
直角坐标串并联机器人的运动平台在运动过程中保持特殊形式的前提下,机构的运动学反解唯一确定,通过对6个直线输入运动参数分别对输出主轴在空间的位置和姿态的敏感性的实证研究与分析,得出机构的上层动平台和下层动平台的输入运动参数对输出主轴的空间位置和姿态变化的敏感性方面所起的不同关键作用,同时还对该机器人的冗余驱动结构形式的敏感性也做了分析,从而知道各输入运动参数在影响输出主轴位姿变化上的差异。
5)  attitude
姿态
1.
Solution of Forecasting-Correcting-Improving Algorithm to Quaternion Differential Equation of SINS Attitude;
基于预测-校正-改进算法解算SINS姿态的四元数微分方程
2.
Research on the Satellite s Geometry Attitude Determination;
卫星姿态的几何确定方法初探
3.
Research on Attitude Search Algorithm for Maneuvering Penetration of Ballistic Missile in Middle-course Flight;
机动弹头中段突防姿态的搜索算法研究
6)  gesture
姿态
1.
Relationships between gestures and speech in spontaneous Chinese speech;
汉语口语对话中姿态与语音信息关系初探
2.
Analysis of position and gesture of robot based on complex vector principle;
基于类复向量原理的机器人位置和姿态分析
3.
Research on the Relationship between Gesture and Speech Information for Human Computer Interaction;
面向人机交互的姿态信息与语音信息关系研究
参考词条
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。