1) exergy consumption ratio
比耗
1.
Furthermore,validates the truth that the least exergy consume ratio is same for any reversible dehumidifying process,and from the least exergy consumption ratio,presents the thermodynamics consummating degree of the dehumi.
综合分析除湿过程中可能存在的5种能量交换方式,给出除湿过程比耗的表达式,提出回收率的概念,并根据理想除湿过程,得到除湿过程的最小比耗。
2) specific energy consumption
比能耗
1.
The paper features experimental data by single-factor experiment which takes the cutting drum parameters of obviously affecting specific energy consumption as variables.
截割比能耗是衡量采煤机滚筒设计优劣的重要指标之一。
2.
The example of multi-objective optimization design shows that load fluctuation and specific energy consumption of cutting head are evidently reduced, which increase working reliability and energy utilization quotiety of roadhea.
优化实例表明,截割头的载荷波动和比能耗得到了明显降低,提高了掘进机的工作可靠性和能量利用率。
3.
According to the mechanics model of single pick, the mathematic model of optimized design based on load torque fluctuation and specific energy consumption of cutting head is built to search optimum kinematic parameters of roadheader by means of computer simulation.
根据单个截齿受力模型,采用计算机模拟的方法建立了基于截割头负载转矩波动和截割比能耗最小的优化设计数学模型,寻求最优的掘进机运动参数。
3) oxygen distribution
耗氧比
1.
Based on the comparison of different oxygen distribution models and the analysis of the oxidation mechanism of Mn, Si and P in BOF refining process, an oxygen distribution model, based on both thermodynamics and kinetics is established.
通过对转炉冶炼过程中耗氧比模型的比较及Mn,Si,P氧化机理的分析,应用冶金热力学和动力学建立了耗氧比模型,并根据生产数据的检验结果与模型预测结果的一致性,得出如下结论:供氧强度决定Mn,Si,P的氧化速率;Mn,Si,P在熔池中扩散系数和初始含量的大小将决定各自耗氧比的起始大小;温度通过反应平衡常数影响耗氧比。
4) regenerative ratio
再生比耗
1.
Analysis of the causes resulting in overabundance of regenerative ratio cost in cation exchangers;
阳离子交换器再生比耗过大的原因分析
5) wear resistance ratio
磨耗比
1.
The effects of the pressure,temperature and time on the properties of sintered diamond compacts are investigated in infiltrating way in this work;sintered diamond compacts of metal additive with the wear resistance ratio of 285×10 3 and without abnormal diamond grain growth are obtained at 1400℃, 5.
8GPa、12min的烧结条件下,烧结出磨耗比为285×103、金刚石颗粒未出现异常长大的金刚石烧结体;分析了烧结方法对烧结效果的影响。
2.
The effects of diamond grain sizes on wear resistance ratio of the sintering diamond compacts are investigated.
本文采用熔渗法和混合法进行了合成金属结合剂金刚石烧结体的对比实验；对实验结果进行了讨论；研究了金刚石的粒度对烧结体磨耗比的影响；探讨了两种方法的使用范
6) Abrasive ratio
磨耗比
1.
Abrasive ratio, thermal stability, impact toughness and cohesive strength are main performance figures of PDC.
磨耗比、热稳定性、抗冲击韧性和结合强度是金刚石复合体的主要性能指标。
2.
By a self designed equipment and given testing conditions, comparative experiments were done to contrast the abrasive ratio of cemented carbide coated with diamond film and other material samples.
利用自行设计的试验装置 ,在设定的试验条件下 ,对金刚石薄膜涂层硬质合金等 3种不同材料试件的磨耗比进行对比试验 ,并对试验结果进行讨论。
补充资料：耗耗
1.方言。老鼠。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条