1) crack initiation stress
起裂应力
1.
Based on the conventional triaxial compression test of Three Gorges granites,the crack initiation stress under different confining pressures can be obtained by studying the crack strain curves.
从三峡花岗岩常规三轴实验出发,通过研究裂纹应变的变化规律,得到不同围压下花岗岩的起裂应力。
2) structural,spalling
(由应力引起的)结构散裂
3) initiation pressure
起裂压力
1.
Hydraulic fracturing initiation pressure models for directional wells in naturally fractured formation;
天然裂缝地层斜井水力裂缝起裂压力模型研究
2.
Effect analysis of perforating parameters upon initiation pressure in low permeability reservoir
低渗透储层射孔参数对起裂压力的影响
3.
It is important for fracturing design and operation to determine hydraulic fracturing initiation pressure and mode.
根据天然裂缝产状和地层地应力状态,建立了水力裂缝3种起裂方式的起裂压力计算模型,给出了水力裂缝起裂方式和起裂压力的判别方法。
4) initial stress
起始应力
5) stress crack
应力开裂
1.
The mechanism of stress cracking and find what the key impact to this problem is researched.
通过对应力开裂机理进行研究和讨论,找出了影响碳酸饮料包装瓶应力开裂的因素,提出了解决思路和方法,并在生产实践中对制瓶工艺进行优化,最终解决了碳酸饮料包装瓶的应力开裂技术难题。
2.
The mechanical properties and stress crack properties of PC/ABS and PC/ABS/PE g MAH blends were studied.
研究了聚碳酸酯与ABS(PC/ABS)及PC/ABS与马来酸酐接枝聚乙烯共聚物 (PC/ABS/PE -g-MAH)共混体系的力学性能和应力开裂性能。
3.
The paper summarizes the causes of the internal stress in injected part and the influencing factors, discusses the measures to eliminate the stress crack, determines the optimum process condition by the orthoqonal method and intnxluces the heat treatment technology and the method of stress inspection.
论述注塑件内应力产生的原因和影响因素,研究消除应力开裂的有效措施,用正交设计法确定最佳注射工艺,介绍热处理工艺和应力检验方法。
6) stress cracking
应力开裂
1.
Exploring LSZH cable and its stress cracking mechanism;
无卤低烟阻燃电缆及其应力开裂的探讨
2.
It researches and discusses the mechanism of stress cracking, and the factors affecting stress cracking of polyester bottle are aimed at.
通过对应力开裂机理进行研究和讨论, 找出了影响碳酸饮料瓶应力开裂的因素, 提出了解决思路和方法, 并在生产实践中对制瓶工艺进行优化, 最终解决了碳酸饮料瓶的应力开裂技术难题。
3.
The mechanism of the stress cracking in the sheath of low smoke HFFR cables with steel tape armour was investigated.
探讨了无卤低烟阻燃铠装电缆护套应力开裂的机理,提出了防止护套应力开裂的方法,在电缆的双层间隙的绕包铠装和无卤低烟阻燃聚烯烃护套之间含有缓冲层,用于消除电缆弯曲时在钢带间隙处外护套上形成的应力集中现象,保护护套不受双层钢带铠装的影响而开裂,因而提高电缆使用寿命和可靠性。
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条