1) saturated oil velocity
饱和油速度
2) Velocity saturation
速度饱和
1.
An improved analytical model is developed to predict the propagation delay of a small size CMOS inverter, which includes the effect of the velocity saturation and the influence of input waveform slope.
提出了一个新的小尺寸 CMOS倒相器延迟模型 ,它考虑了速度饱和效应以及非阶梯的输入信号对延迟的影响并给出了倒相器快输入响应与慢输入响应的判据 ,模型计算结果与SPICE BSIM1模型的模拟结果吻合得很好 。
3) saturation rate, saturation speed
饱和速度
4) oil saturation
油饱和度
1.
4 and is made with 81 pairs of microelectrodes placed in lines to measure the electric resistance values,from which water and oil saturations are calculated.
4,由埋置的81对微电极测量81个点处的电阻率,计算各该处含水饱和度,求得含油饱和度。
2.
The experiment used the real low permeability core and condensate gas sample with high gas condensate content(containing gas condensate:364g/m3)both of which come from Qiaobai gas field in Zhongyuan to research the effects of the porous media and original water saturation on gas condensate saturation and residual oil saturation and that the porous media on dew pressure of condensate gas.
采用中原桥白气藏实际低渗透储层岩心和配置的高含凝析油型(凝析油含量364g/m3)凝析气样分别从实验、数值模拟角度研究衰竭过程中,多孔介质、初始水饱和度对凝析油饱和度和残余油饱和度的影响,以及多孔介质对凝析气露点压力影响。
5) oil saturation
含油饱和度
1.
Physical simulation of the control of source rock oil saturation on forming lithological oil pools;
围岩含油饱和度控制岩性油藏成藏的物理模拟
2.
Method of improving calculation accuracy of oil saturation;
提高含油饱和度计算精度的方法研究
3.
Relationship between capillary pressure data of intrusive mercury method and oil saturation;
也谈压汞资料与含油饱和度的关系
6) oil-bearing saturation
含油饱和度
1.
Discussion on Computing Oil-Bearing Saturation from Fluorescence Intensity;
利用荧光强度求取含油饱和度的探讨
2.
Taking the abroad NMR instrument as an exam ple, the author introduced the calculation formula for effective porosity, perme ability evaluation model, movable and irreducible fluid saturation, and effectiv e oil-bearing saturation.
以国外核磁共振(NMR)仪器为例,介绍了有效孔隙度的求取、渗透率评价模型、可动、束缚流体饱和度、有效含油饱和度等的计算公式。
3.
A simplified calculating method is also presented based on oil-bearing saturation formula and experience formula.
以含油饱和度公式为基础 ,结合经验公式 ,提出了简化计算方法。
补充资料:切削油及切削速度
切削油剂有润滑、冷却及抗融著的三种作用,此称为切削油的三要素。攻牙的情形进行著非常复杂的切削作用,所以必须给予充分切削油以利其作业。 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
表10所示是标准切削速度与合滴切削油剂。 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条