1) frame-supported multi-ribbed slab structure
框支密肋壁板结构
1.
Rational ratio of lateral stiffness for frame-supported multi-ribbed slab structure in transfer stories
框支密肋壁板结构转换层刚度比的合理取值
2.
Based on the former research results,the calculation measure for the wall beam of frame-supported multi-ribbed slab structure has been studied in this paper.
结合课题组前期研究成果,对框支密肋壁板结构墙梁的计算方法进行研究。
2) frame-supported multi-ribbed wall beam
框支密肋壁板结构墙梁
1.
Research on Load-Bearing Performance and Design Method of Frame-Supported Multi-Ribbed Wall Beam;
框支密肋壁板结构墙梁受力性能及设计计算方法研究
2.
Considering the factors of height-to-span ratio of the trimmer beam,height-to-span ratio of the wall and height-to-length ratio of the bottom frame column section,the orthogonal design of one-span frame-supported multi-ribbed wall beam without opening was done and the internal forces of the trimmer beam were calculated with the finite element method.
考虑托梁高跨比、墙体高跨比、底部框架柱的截面高度与其长度之比诸因素,采用正交试验设计,通过对单跨无洞框支密肋壁板结构墙梁有限元计算结果的直观分析和方差分析,对其托梁内力的影响因素进行了显著性分析,并在此基础上利用回归分析得到了考虑墙梁组合作用的托梁内力系数。
3.
Considering the factors of height-to-span ratio of the trimmer beam,height-to-span ratio of the wall,section height-to-length ratio of the bottom frame column and the position of the opening in the wall,the orthogonal design of single-span frame-supported multi-ribbed wall beam with opening is done and the influence of the opening on the internal force of the trimmer beam is analyzed.
考虑托梁高跨比、墙体高跨比、底部框架柱的截面高度与其长度之比、墙体洞口位置诸因素,采用正交试件设计,对单跨带洞框支密肋壁板结构墙梁中洞口对托梁内力的影响进行了分析,进而通过回归分析得到了单跨带洞框支密肋壁板结构墙梁考虑墙梁组合作用的托梁内力系数。
3) structure of multi-rib panel
密肋壁板框架结构
4) Multi-ribbed Slab with Light Fram Structure
密肋壁板轻框结构
1.
Analysis and Research on Multi-ribbed Slab with Light Fram Structure s Non-linear Earthquake Response;
密肋壁板轻框结构非线性地震反应分析与研究
补充资料：板框组件
分子式：
CAS号：
性质：也称平板式膜组件。由平板式膜和支撑板组成的膜分离单元设备。支撑板的两侧表面有窄缝，其内腔有供透过液流通的通道，支撑板的表面与膜相贴，对膜起支撑作用，有的组件还设有导流板，对料液起导流作用。板框组件分为系紧螺栓式、耐压容器式等几种。由许多相同的板框组件组装在一起构成板框式膜器。
CAS号：
性质：也称平板式膜组件。由平板式膜和支撑板组成的膜分离单元设备。支撑板的两侧表面有窄缝，其内腔有供透过液流通的通道，支撑板的表面与膜相贴，对膜起支撑作用，有的组件还设有导流板，对料液起导流作用。板框组件分为系紧螺栓式、耐压容器式等几种。由许多相同的板框组件组装在一起构成板框式膜器。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条