1) injection characteristics
喷射特性
1.
Study of fuel injection characteristics for small air-cooled gasoline generator sets
小型风冷汽油发电机组燃油喷射特性
2.
Hereon,the nozzle coefficient s influence on the injection characteristics of fuel supply system,the performance and emission of diesel engine were revealed.
通过理论分析及高压流量试验,分析了喷油嘴结构参数,如压力室形状、喷孔直径、喷孔长度、喷孔锥角等对流量系数的影响,并进行了喷油嘴流量系数对燃油系统喷射特性和柴油机性能、排放的影响研究。
3.
In order to develop a new type of oil supplying system to replace the traditional pump pipe nozzle system, the injection characteristics of common rail accumulator electronic unit injector are studied.
研究共轨蓄压式电控泵喷嘴系统的喷射特性 ,取代传统的泵 -油管 -喷嘴系统 。
3) spray characteristics
喷射特性
1.
The influence of injection pressure and injection rate shaping on the spray characteristics was investigated.
提出了双压共轨的概念,阐明了双压共轨系统(DPCRS)的结构组成和工作原理,建立了系统仿真模型,对系统的喷射特性进行了仿真研究。
4) performance of fuel injection system
燃油系统喷射特性
5) characteristics of nozzle
喷嘴特性
1.
Study on arrangement and characteristics of nozzles for wet flue gas desulfurization spray scrubber;
湿法烟气脱硫系统喷淋塔喷嘴特性与布置研究
6) spray characteristics
喷雾特性
1.
An experimental study on spray characteristics of film coating;
薄膜包衣喷雾特性实验研究
2.
Investigation on spray characteristics of bi-centrifugal swirl injector
双组元离心式喷注器的喷雾特性初步研究
3.
Constitute and principle of the flow characteristics and spray characteristics test apparatus of electronically-controlled injector are presented.
介绍了所设计的电控喷油器流量特性和喷雾特性测试装置的组成及原理,并对某一喷油器的测试数据进行了分析总结。
补充资料:DWP喷射气流干燥机
工作原理:
DWP型属喷射气流带式干燥类型,热风以狭缝流或孔束流向下或上下同时喷向输送带上的物料,由于喷射气带高达15m/s以上,故对流传热的传热膜极薄,传热系数大,干燥速度快。该设备用于不透气类物料时,上面喷射气流仍返回上面,下面喷出的气体仍返出下面,再参与循环。对透气性物料如涂膜布干燥等,也适用于片状物料及一些特殊物料的干燥。如果采用双向气流喷射,板材之类物料干燥后变形小。喷射气流干燥使用热源可以是蒸气、电、热风炉及燃油烟道气等。
应用范围:
喷射气流带式干燥专用设备,比如纸浆干燥一般为S型或M形结构的多层式,大型纸浆模则为单层式。前者输送为吊蓝型,后者为为网带输送型。并且热风温度、循环气体量、湿度、气流速度及气流束形式不为其它物料所通用,实际差别很大。
对用户的咨询,我厂工程师会迅速作出详细的合理的设计方案,愿与用户一道,促使我们的设备性能更好,效益更好。
技术参数:
名称\参数\序号 | DWP-Ⅰ | DWP-Ⅱ | DWP-Ⅲ | |
带宽m | 1.6 | |||
干燥段长m | 8 | |||
铺料厚mm | 10-80 | |||
使用温度oC | 50-120 | |||
蒸汽压力Mpa | 0.2-0.6 | |||
换热面积m2 | 330 | 296 | 259 | |
干燥时间h | 0.2-1.2 | |||
风机数量 | 3 | 2 | 2 | |
传动机功率Kw | 0.75 | |||
风机功率 KW | 7.5*3*2 | 7.5 3 | 7.5 3 | |
外形尺寸 | 10*2.1*3.6 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条