1) S-Function Builder
S-Function Builder
2) S-function
S-function
1.
Simulation of PWM control system based on S-Function;
基于S-Function的PWM控制系统仿真
2.
The control system is simulated by the simulink of MATLAB; the parameter turning module and the nonlinear model of the magnetic bearings are realized by S-function.
在MATLAB的SIMULINK环境下构建控制系统模型,用S-function编写变参数PID控制器的参数变化规则模块和磁悬浮轴承的非线性模型,并进行了动态仿真。
3.
Based on the analysis of the S- Function block hardware driver,an S-Function written in C language is introduced,which is used to call device driver and manipulate data-acquisition card.
在分析S-Function模块硬件驱动原理的基础上,介绍了用C语言编写S-Function函数,以调用设备驱动程序操作采集卡。
3) S Function simulation
S-Function仿真
4) Green's function
Green s function
5) BUILDERnschweil
BUILDER
6) C++ Builder
C++ Builder
1.
Implementation of Serail Communication on RS232 by C++ Builder;
基于C++ Builder的RS232串行通信实现
2.
Program Design of Communication between PC and MCU Based on C++ Builder;
基于C++ Builder的PC机与单片机通信程序设计
3.
Design and analysis on multi-tier distributed architecture based on C++ Builder;
基于C++ Builder的多层分布式结构设计与分析
参考词条
DSP Builder
Model Builder
BorlandC++Builder
Power-Builder
HMI Builder
COM Builder
C~(++) Builder
Node Builder
SOPC Builder
Platform Builder
Install Builder
Builder/SQL
C~(++)Builder
甲钴胺胶囊
出线
补充资料:thermodynamic function of mixing
分子式:
CAS号:
性质:把n1mol组分1和n2mol组分2混合形成均相系统(如溶液)时的热力学函数变化。以焓(H)为例:ΔmixH=H混合后-H混合前=(n1H+n2H2)-(n1+n2);其中,H1及H2分别为组分1及组分2的偏摩尔焓,及分别为纯组分1和纯组分2的摩尔焓。Δmix在定压下叫混合热(heat of mixing)。对于由两个纯液态组分形成的理想溶液:ΔmixH=0,ΔmixS=-R[n1lnx1+n21nx2],ΔmixV=0,ΔmixG=RT[n1lnx1+n2lnx2]
CAS号:
性质:把n1mol组分1和n2mol组分2混合形成均相系统(如溶液)时的热力学函数变化。以焓(H)为例:ΔmixH=H混合后-H混合前=(n1H+n2H2)-(n1+n2);其中,H1及H2分别为组分1及组分2的偏摩尔焓,及分别为纯组分1和纯组分2的摩尔焓。Δmix在定压下叫混合热(heat of mixing)。对于由两个纯液态组分形成的理想溶液:ΔmixH=0,ΔmixS=-R[n1lnx1+n21nx2],ΔmixV=0,ΔmixG=RT[n1lnx1+n2lnx2]
说明:补充资料仅用于学习参考,请勿用于其它任何用途。