1) Midium-sized shear test
中型剪切试验
2) middle-sized shear test
中型剪试验
1.
This paper introduces the general situation and geological conditions of Wenyuhe Reservoir,and expounds the procedures and results analysis of the middle-sized shear test on the rock in weak interlayer of Wenyuhe Reservoir.
介绍了文峪河水库的概况和工程地质情况,阐述了文峪河水库软弱夹层岩石中型剪试验过程和结果分析。
3) micro shear test
微型剪切试验
1.
The characteristic values of micro shear test and tensile test of alloy aluminium were determined and the quantitative expressions of these characteristic values were studied.
测定了铝合金的微型剪切试验和拉伸试验的性能参数,研究了这些性能参数之间的数量关系式。
2.
The characteristic values of micro shear test and tensile test of aluminium alloy were determined and the quantitative expression of these characteristic values were studied.
通过测定铝合金微型剪切试验和拉伸试验的性能参数,研究得出了这些性能参数之间的数学关系式。
4) microshear test
微型剪切试验
1.
A new test method of estimating properties of material and welded joint, the microshear test, has been developed to investigate the microshear strength and microshear plasticity as well as microshear toughness of X60 and X65 pipeline steels and its spiral submerged arc welded joints.
采用一种新型的金属材料及焊接接头力学性能试验方法——微型剪切试验，研究了Ｘ６０和Ｘ６５管线钢及其螺旋埋弧焊焊接接头的微剪强度、微剪塑性、微剪韧性等性能参数。
2.
The nonuniformity of microstructure and mechanical properties in the GH150 butt joint of argon arc welding is investigated by means of distribution in the welded zone measured by the metallographic study and microshear test.
研究了ＧＨ１５０合金对接氩弧焊接头显微组织和力学性能的不均匀性，用金相分析和微型剪切试验等方法得到了该焊接接头各区域的微观组织和力学性能分布特性。
5) large?scale shear test
大型切剪试验
1.
A large?scale shear test on the gravel piles and its composite foundation is conducted in Guangdong province, China.
介绍珠江下游岸边三次大型碎石桩及其复合体的现场大型切剪试验 ,并获得复合地基的强度指
6) shear test
剪切试验
1.
Analysis of landslide mechanism from shear test;
从剪切试验分析滑坡机理
2.
Lots of tests show that the cohesion of rock measured from a triaxial test is always greater than that from shear test.
大量的试验结果表明 ,由三轴试验测得的岩石凝聚力总是大于剪切试验的结果 ,本文分别从岩石强度理论及实验方法的角度分析了产生这种误差的原因 ,建议今后在给出岩石(煤 )的凝聚力和内摩擦角时应标明是由何种试验方式所测得的。
3.
Selection of the highstrength bolts,determination of fastening torque values,quality checking of bolts,and shear tests of bolts are illuminated based on the design of the iron tower.
结合大跨越铁塔设计,对高强度螺栓的选择、紧固扭矩值的确定、螺栓的质量检验、螺栓的剪切试验等情况作了论述。
补充资料：机械工程材料:剪切试验
测定材料在剪切力作用下的抗力性能﹐是材料机械性能试验的基本试验方法之一。主要用於试验承受剪切载荷的零件和材料﹐如锅炉和桥梁上的铆钉﹑机器上的销钉等。剪切试验在万能试验机上进行﹐试样置於剪切夹具上﹐加载形式有单剪和双剪两种(见图 剪切试验加载示意图 )
﹐试样在剪切载荷P 作用下被切断。单剪时﹐P 除以试样截面积A ﹐可得出剪切强度b﹐b=P /A ﹔双剪加载时b=P /2A 。
﹐试样在剪切载荷P 作用下被切断。单剪时﹐P 除以试样截面积A ﹐可得出剪切强度b﹐b=P /A ﹔双剪加载时b=P /2A 。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条