说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 倾斜偏心荷载
1)  eccentric and inclined loads
倾斜偏心荷载
1.
Analysis of single piles under eccentric and inclined loads in layered soils;
成层地基中倾斜偏心荷载下单桩计算分析
2.
The behavior of piles in layered clays under eccentric and inclined loads can not be analyzed by traditional finite pole element method if P-Δ effect is significant.
传统有限杆单元法不能考虑倾斜偏心荷载下基桩的P-Δ效应,假定桩身位移为三次幂函数,结合倾斜偏心荷载下单桩受力微分方程确定的桩身弯矩、剪力与桩身水平位移关系,导得具有简洁形式、计入P-Δ效应的杆单元刚度方程,进而得到改进的有限杆单元方法,并给列出了用该法进行成层地基中倾斜偏心荷载、桩自重、水平分布荷载、竖向分布荷载和竖向分散集中荷载综合作用下并考虑桩身倾斜影响基桩内力位移分析的具体计算步骤。
2)  oblique eccentric loading
斜偏心荷载
3)  inclined loads
倾斜荷载
1.
Bending moment analysis under inclined loads based on non-linear variational principle s high cap pile group;
高承台群桩在倾斜荷载作用下的弯矩分析
2.
Bearing capacity calculation of strip footing under inclined loads with upper bound theorem and SQP method;
基于SQP优化和上限法的倾斜荷载下条形浅基础极限承载力计算
3.
Research on Nonliner Element Free Method and Its Applying in Mechanic Analysis of Pile Group under Inclined Loads;
倾斜荷载下群桩受力的非线性无单元分析方法与应用研究
4)  inclined load
倾斜荷载
1.
The Small Scale Model Test Study on Inclined Load Capacity of Suction Caisson;
倾斜荷载作用下吸力式沉箱抗拔性能试验研究
2.
Finite element analysis of bearing capacity of pile under inclined load in layered soil
成层土中倾斜荷载作用下桩承载力有限元分析
3.
The effect of angle of inclination at the interface of a viscous fluid and thermoelastic micropolar honeycomb solid due to inclined load is investigated.
研究倾斜荷载作用在黏性流体与热弹性微极蜂窝结构固体界面上时,荷载倾斜角的影响。
5)  tilting load
倾斜载荷
6)  inclined loading
倾斜荷载
1.
Studies of bearing capacity of bucket foundation against inclined loading
倾斜荷载作用下桶形基础承载力特性研究
补充资料:在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.

1)连接PA,PB. A(-100,0,0) B(100,0,0)



图1



在当前坐标下:


2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;


3)连接CD;


4)以CD为直径画圆;


5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;


6)过O作CD的垂线,交圆于E,F;



图2



7)用三点UCS命令,取三点为:O,P,C;


8)过点O作PO的垂线GO,交PC于G;



图3



9)再次用三点UCS命令,取三点为O,F,G;


10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;



图4



11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.


12)删除辅助线条.



图5

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条