1) high axial compression ratio
高轴压比
1.
Experimental study on ductility and bearing capacity of concrete frame columns with central reinforcement under high axial compression ratio;
高轴压比下加芯混凝土框架柱延性与承载力试验研究
2.
Through the test of concrete frame columns with central reinforcement and general concrete frame column under high axial compression ratio and cyclic lateral loading,the P-Δ hysteresis curve,stiffness degradation,viscous damping coifficients etc.
通过加芯混凝土框架柱和普通混凝土框架柱在高轴压比下的低周往复加载试验,对试件的P-Δ滞回曲线、刚度退化和等效粘滞阻尼系数等进行了研究,分析了加芯混凝土框架柱刚度和耗能的影响因素。
3.
Based on the experimental study on six separated columns with high axial compression ratio and under horizontal cyclic loading, this paper analyzes the effects of axial compression ratio and stirrup reinforcement ratio on the seismic behavior of the separated columns, including rigidity, cracking, maximum bearing capacity, failure features and hysteresis curve etc.
本文通过六根分体柱在高轴压比和低周反复水平荷载作用下的试验研究,分析了轴压比、配箍率等对分体柱的刚度、裂缝、最大承载能力、破坏形态及其滞回特性等抗震性能的影响;分析了过渡区设置和斜向水平荷载对分体柱受力性能的影响。
2) axial compressive ratio
轴压比
1.
Studies on limit values of axial compressive ratio of steel reinforced concrete column;
型钢混凝土柱轴压比限值的研究
2.
Natural period of vibration,axial compressive ratio,bottom shear of column and drift angle were also researched.
结合工程实例,对钢筋混凝土异形柱框架结构在不同方向的水平地震作用下进行受力分析,对自振周期、轴压比、柱底层剪力和层间位移角进行分析。
3.
The effect of the width-to-thickness ratio and the axial compressive ratio on the hysteretic behav.
应用大型有限元软件ABAQU S,采用考虑几何和材料非线性的S4R 5壳单元和线性随动强化模型,考虑角部冷成型强化效应的影响,建立了常轴力、循环弯矩荷载作用下的C型钢构件有限元模型,分析了构件宽厚比和轴压比对冷成型薄壁C型钢构件滞回性能的影响。
3) axial compression ratio
轴压比
1.
Study of limit values of axial compression ratio for concrete-filled square steel tubular columns;
方钢管混凝土柱轴压比限值的研究
2.
Influence of neatral-axis angle on ultimate axial compression ratio for T-shaped RC columns;
中和轴角对钢筋混凝土T形截面柱界限轴压比的影响
3.
Discussion on limit values of axial compression ratio of frame columns for high building;
高层建筑框架柱轴压比限值研究
4) axial pressure ratio
轴压比
1.
Adjustment of axial pressure ratio in designing frame structural systems with special-shape column;
异型柱框架体系设计中轴压比的调整
2.
Frame column section choice has become the important content for design of frame structural residence,the article describes the estimation of column s axial pressure ratio,the width between side span column and corner column should meet the reguirement and the eccentricity of frame structure s beam and column.
框架柱截面的选择已成为框架结构住宅设计的重要内容,通过柱轴压比的估算、边跨柱与角柱的宽度应满足的要求以及框架梁柱偏心问题的注意方面来阐述抗震区框架柱截面的选择。
3.
Based on the reasonable mechanics models the paper emphatically analyzed the influence on the performance of the slitted shear wall about the axial pressure ratio,concrete strength.
通过建立合理的力学模型,着重研究轴压比、混凝土强度对免拆模复合带缝剪力墙性能的影响。
5) axial load ratio
轴压比
1.
Experimental study on seismic behavior of frame columns with high axial load ratio subjected to low cyclic loads;
周期反复荷载作用下高轴压比框架柱抗震性能的试验研究
2.
Experimental study on seismic behavior of high strength concrete short-columns with high axial load ratio;
高轴压比高强砼短柱抗震性能试验研究
3.
Discussion on axial load ratio limits of circular steel tube columns filled with steel-reinforced concrete;
关于钢骨-钢管混凝土组合柱轴压比限值问题的讨论
6) bearings ratio to press
轴承比压
1.
It puts forward the key factor which influences of enhancing pressure of gear pump is the bearings ratio to press and the whole stiffness of gear pump, and gives some methods.
文章通过试验数据和理论计算等分析了影响提高齿轮泵额定压力的因素,提出了影响齿轮泵上压力等级的关键因素是轴承比压和泵的整体刚度,并给出了一些方法。
补充资料：压轴
1.见"压胄子"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条