1) The light center of gravity method
光重心法
1.
The light center of gravity method is applied to processing optic fiber exited spot signal.
采用"光重心法"对光斑信号进行处理。
2) center of light emitting area
发光重心
3) gravity center of light spot
光斑重心
1.
Distal location method of interlocking intramedullary nails based on gravity center of light spot;
基于光斑重心的交锁髓内钉远端定位方法研究
4) Weighted-centroid
权重重心法
5) method of barycenter
重心法
1.
The method of barycenterdetermines the zoning sequence by using the space position of anamalous concentrationcenter for each element,and it can be used in the calculating the sequence of axial zoning andtransversal zoning,and could correct the defects of other methods, therefore it is a use.
重心法以每个元素异常浓集重心的空间位置排出分带序列，同时适用于轴向分带和横向分带序列的计算，克服了其它方法中存在的缺陷，是一个很有应用前景的方法。
2.
The sub-pixel accuracy in abstracting the fringe-centerlines can be obtained by the method of barycenter after preprocessing the fringe picture using grating projection.
对光栅投影条纹图像进行预处理,采用重心法提取条纹中心线位置,可以获得亚像素级的精度。
3.
The method of barycenter, which can obtain the sub-pixel accuracy to abstract the fringe-centerlines, is presented in this paper after preprocessing the picture using grating projection.
本文对光栅投影条纹图像进行预处理,提出采用重心法提取条纹中心线位置,可以获得亚像素级的精度;接着修补条纹中心线,采用模板技术跟踪条纹的走向,可求出条纹中心线相对参照平面条纹中心线的相对偏移量。
6) center of gravity method
重心法
1.
Error analysis of the center of gravity method when used to get the position of a facula;
利用重心法求光斑信号位置的误差分析
2.
The detector based on MWPC has a sensitive aera of 200×200 mm2,and with center of gravity method to get X-ray position.
探测器采用多丝正比室(MWPC)结构,有效面积200×200mm2,采用阴极感应读出,由电荷重心法确定入射X射线位置。
3.
At first, the center of gravity method is used to obtain the clustering centre of each load dynamic characteristics classification; then by identifying th.
以基于实测响应空间的负荷动特性分类方法为基础,提出了一种负荷动特性直接综合方法:采用重心法原理确定各类负荷特性的聚类中心作为其等效实测响应样本;通过对各个聚类中心等效样本进行参数辨识以得到相应类的综合模型参数;运用判别分析法确定新实测样本的所属负荷特性类别并形成修正后的新的聚类中心等效样本;对加入新样本后的聚类中心等效样本进行参数辨识以得到相应类的修正综合模型参数。
补充资料：比色分析法(见紫外—可见分光光度法)
比色分析法(见紫外—可见分光光度法)
比色分析法见萦外一可见分光光度法。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条