1) injection current
注入电流
1.
Theoretical analysis and characterization of injection current distribution and influences on optical near-field modes in gain-guided vertical-cavity surface-emitting lasers;
增益导波垂直腔激光器注入电流空间分布及其对激光近场模式影响的理论分析和表征
2.
After the node sequence injection current is got,considering the influence from other sequence components,the following solution is applied:for positive and negative sequence problems ,node voltage is solved by for/backward sweep method;for zero sequence problem,node voltage is.
在求得各序间相互影响各序节点注入电流之后,采取以下求解方法:对正序、负序网络沿辐射支路用前推回代的方法求解,对零序网用常规高斯塞德尔(Gauss-Seidel)迭代法求解,这样可加快求解的速度。
3.
This paper proposes an injection current based three phase power flow method.
提出了节点注入电流的三相潮流分析方法。
2) current injection
电流注入
1.
This paper introduces the method to achieve time association in current injection experimentation.
本文介绍了在电流注入试验中实现时间关联的方法,并采用该方法得到了典型电路失效概率分布。
2.
In this paper,the EMP failure modes of solid state relays were obtained by current injection method.
本文通过电流注入法对某型直流固态继电器输入端与输出端的电磁脉冲损伤机制进行了实验研究,确定了两种失效模式。
3.
The electromagnetic pulse(EMP) damage mechanism and failure modes are obtained for the input port and output port of solid state relays by current injection method.
采用电流注入法对某型直流固态继电器输入端与输出端的电磁脉冲损伤机制及失效模式进行了实验研究,结果表明:输入端注入电磁脉冲信号时,输出端会产生误动作,并可造成输入电路中三极管BE节产生短路损伤,导致输入端施加控制信号时输出端无法导通;输出端注入电磁脉冲信号时,可造成输出电路中MOSFET管的栅极和漏极产生短路损伤,导致输出端短路。
3) Current bleeding
电流注入
1.
A current bleeding CMOS mixer with complementary transconductance stage is designed.
设计了一种基于跨导互补结构的电流注入混频器,通过在吉尔伯特混频器电路的本振开关管源极增加PMOS管形成电流注入电路减小本振端的偏置电流,改善电路的闪烁噪声和增大电路的增益。
4) current-influx model
电流注入型
1.
Application of general Tellegen's theorem in retaining-nonlinearity power flow calculation based on current-influx model
广义Tellegen定理在保留非线性电流注入型潮流计算中的应用
2.
An algorithm which combined eigenvalue structure analysis(ESA) with current-influx model and gave the information about weak nodes and lines in grid was presented.
本文将特征结构方法与电流注入型相结合,推导出一种判断电力系统薄弱节点,薄弱线路的方法。
5) current injection method
电流注入法
1.
This paper describes a current injection method to detect the rotor flux position of the salient-pole brushless DC motor.
介绍了凸极无刷直流电动机转子位置检测的电流注入法。
2.
At the end,the example of Luodong Substation is listed to verify that current injection method is not applicable to substations under complex operation mode,then another solution is brought up.
最后以罗洞站抑直方案为例,验证了电流注入法不适用于复杂运行方式的变电站,并提出了解决方案。
6) Electron beam implantation
电子流注入
补充资料：标准冲击电流波形(见冲击电流发生器)
标准冲击电流波形(见冲击电流发生器)
standard impulse current wave form
blaozhun ehonglld}0n4一u box]ng标准冲击电流波形(standard impulse currentwave form)见冲击电流发生器。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条