说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 偏心受压
1)  eccentric compression
偏心受压
1.
Study on eccentric compression of rapidwall with concrete filled every one or more holes;
纤维增强石膏板隔孔灌注混凝土偏心受压性能研究
2.
Experimental study on deformation performance of median long columns with Yellow River silt cellular bricking structures subjected to eccentric compression;
黄河淤泥多孔砖砌体中长柱偏心受压变形性能试验研究
3.
Study of stress-strain relation of concrete filled steel tubular eccentric compression column;
钢管混凝土偏心受压应力-应变关系模型研究
2)  Eccentric pressure
偏心受压
1.
Using the real stress\|strain relation of concrete material,a method to determine the ultimate load of concrete circular\|section column under eccentric pressure is discussed,and an ultimate load versus eccentricity curve is obtained.
采用规范规定的混凝土应力 -应变关系 ,对圆形截面混凝土偏心受压构件的极限承载力作了理论分析和计算 ,得到极限承载力 -荷载偏心距曲
3)  little eccentric compression
小偏心受压
1.
Direct calculation of symmetric reinforcement for rectangular cross sectional little eccentric compression member;
矩形截面小偏心受压构件对称配筋的直接计算
4)  eccentrically compressed column
偏心受压柱
1.
Taking the parameters of load eccentricity e_0/h,slenderness ratio l_0/h as variables,bond-slip tests were carried out on 20 SRC eccentrically compressed columns.
以荷载偏心距 e_0/h、构件长细比 l_0/h 为主要参数,进行了20根型钢混凝土偏心受压柱的粘结滑移性能试验,观察了试件的破坏形态,分析了型钢混凝土内部粘结应力和滑移的分布规律。
5)  large eccentric compression
大偏心受压
1.
Calculation of bearing capacity for steel reinforced concrete=column subjected to large eccentric compression load;
钢骨混凝土大偏心受压柱承载力计算
6)  eccentrically compressed pile
偏心受压桩
1.
The computing method for piles recommended in the specifications for architectural design of ground base(GB 5007-2002) is comparatively applicable to the calculation of axially compressed piles,but rather complicated to that of eccentrically compressed piles.
建筑地基基础设计规范(GB50007 2002)给出的桩身计算方法对轴心受压桩较为适用,但对于偏心受压桩的计算则非常繁琐。
补充资料:在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.

1)连接PA,PB. A(-100,0,0) B(100,0,0)



图1



在当前坐标下:


2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;


3)连接CD;


4)以CD为直径画圆;


5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;


6)过O作CD的垂线,交圆于E,F;



图2



7)用三点UCS命令,取三点为:O,P,C;


8)过点O作PO的垂线GO,交PC于G;



图3



9)再次用三点UCS命令,取三点为O,F,G;


10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;



图4



11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.


12)删除辅助线条.



图5

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条