1) self-elevate resistance
自举电阻
1.
That is to say when self-elevate resistance Rg meets low noise condition,the circuit noise disadvantage effect will decrease to minimum and then overlook it.
即:当自举电阻Rg满足低噪声化条件时,自举电路对原电路噪声的不利影响就可以减到最小而可以忽略不计。
2) booster high impedance
自举高阻
1.
Introduce several typical application amplifier: basic reverse proportion amplifier,reverse amplifier with high impedance made up of T meshwork,reverse amplifier with booster high impedance,basic differential amplifier;differential amplifier of high radical mode bound.
并介绍几种典型的应用放大器:由цA741组成的基本放大器、T型网络高输入阻抗放大器、自举高阻反相放大器;基本差动放大器;高基模范围的差动放大器。
3) bootstrap current
自举电流
1.
The alignment of bootstrap current in tokamak;
Tokamak中自举电流的剖面准直性
2.
The bootstrap current produced by fusion born alpha particles is investigated.
本文对聚变产生的α粒子自举电流进行了研究,研究中采用了简便的Pade近似形式,同时考虑了回旋角散射效应和慢化过程中牵引作用的影响,给出了α粒子自举电流计算的理论表达式。
3.
This simulation takes into account of the plasma bootstrap current,ion cyclotron resonance heating and fast wave current drive.
模拟中考虑了自举电流,并加入了离子回旋共振加热ICRH和快波电流驱动FWCD,得到了中心电子温度4。
4) bootstrap circuit
自举电路
1.
This paper introduces the application of Mitsubishi Intelligent Power Module PS22056 in the UPQC main circuit,expatiates upon the selecting method for PS22056 peripheral parts,the calculating methods of main parameters,Experiments are made and the results show that the circuit can stay stable at 10 kHz,bootstrap circuit can stabilize driving voltage at about 14.
介绍了三菱1200V DIP-IPM模块PS22056的在UPQC主电路中的应用,阐述了PS22056外围器件的选择方法、主要参数的计算方法,并进行试验,试验结果证明电路可以稳定工作在10 kHz的频率,自举电路可以很好地将驱动电压稳定在14。
2.
Problems were analyzed on the standby power loss of traditional bootstrap circuit in the isolation power source design.
分析了在隔离型电源设计中传统自举电路待机功耗存在的问题,介绍了一种可降低待机功率的自举电路,并给出了详细的实验电路和参数及实验结果。
3.
The bootstrap process of intelligent power module (IPM) bootstrap circuit was analyzed.
对智能功率模块(IPM)自举电路的自举过程进行了分析。
5) bootstrap charge circuit
自举充电
1.
The third generation IPM of Mitsubishi s PS21564 and its working principle, charging process of exclusive bootstrap charge circuit, the reliable and practical connection mode were presented in detail.
介绍了一种新型基于智能功率模块开关磁阻电动机功率电路,研究了日本三菱公司生产的第三代智能功率模块PS21564的工作原理及其特有的自举充电电路的充电过程及其可靠实用的电路连接方式,并给出仿真结果,证明了此种电路是一种方便可行的开关磁阻电机功率电路。
补充资料：铂电阻温度表(见电阻温度表)
铂电阻温度表(见电阻温度表)
表。bod旧nZu wendubiao铂电阻温度表见电阻温
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条