说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> APACHEⅡ积分模型
1)  APACHE II models
APACHEⅡ积分模型
2)  APACHEⅡ score
APACHEⅡ积分
1.
Effects of continuous veno-venous hemofiltration on serum C-reactive protein level and APACHEⅡ score in patients with multiple organ dysfunction syndrome
连续性静脉-静脉血液滤过对多脏器功能障碍综合征APACHEⅡ积分及C反应蛋白的影响
3)  APACHEⅡ models
APACHEⅡ模型
4)  APACHEⅡ score
APACHEⅡ评分
1.
Clinical value of APACHEⅡ score system and organ function monitoring in cases with multiple trauma;
APACHEⅡ评分及器官功能监测在多发性创伤治疗中的价值
2.
Objective: To investigate the relationship between the changes of platelet in critically ill patients and APACHEⅡ score.
目的:研究危重病患者血小板水平变化与APACHEⅡ评分的关系。
3.
And the data of FIB and D-D of SAP group have positive correlation with the APACHEⅡ score (r=0.
05),并且SAP患者FIB和D-D值与APACHEⅡ评分值之间存在正相关关系(r=0。
5)  Acute Physiology and Chronic Health Evaluation Ⅱ/Ⅲ(APACHEⅡ/Ⅲ)
APACHEⅡ/Ⅲ评分
1.
Objective To compare the clinical value of Acute Physiology and Chronic Health Evaluation Ⅱ/Ⅲ(APACHEⅡ/Ⅲ)system and Simple Acute Physiology Score Ⅱ(SAPSⅡ)system in predicting the prognosis of liver failure.
目的比较APACHEⅡ/Ⅲ评分和SAPSⅡ评分系统评估我国肝衰竭患者预后的临床应用价值。
6)  APACHEⅡscore
APACHEⅡ评分
1.
Results The APACHEⅡscore was 13-67(33.
方法对156例重型肝炎患者应用APACHEⅡ评分,分析评分对预后的预测价值,并根据评分结果指导护理工作安排和护理措施的制定。
2.
The values of APACHEⅡscore were calculated and the incidence of upper gast.
方法对2005年1月至2006年11月间,发病时间≤48h的108例SAP患者,采用试纸法检测胃液pH值变化,观测SAP患者人院时及入院后72h平均胃内pH值及pH值>4、>6的时点数变化,并与APACHEⅡ评分及上消化道出血进行比较。
3.
Methods:193elder critical patients were enrolled in this study,and allocated into groupⅠ(<15scores),groupⅡ(15~20scores)and groupⅢ(>20scores)according to APACHEⅡscore.
方法:将急诊193例患者,入院时进行APACHEⅡ评分及入院第1、3、7、10天进行血小板计数检测。
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条