1) shearing-bonding strength
黏结剪切强度
1.
Effects of nano-diamond filler on shearing-bonding strength and micro-hardness of pit and fissure sealant;
纳米金刚石填料对光固化窝沟封闭剂黏结剪切强度和表面显微硬度的影响
2) shear bond strengths
剪切黏结强度
3) shear viscosity
剪切黏度
1.
The proposed model indicates that the yield stress is one of the main causes for the shear-thinning effect and reveals why some materials possess double-Newtonian regions with the shear viscosity in the first region higher than that in the second region.
它揭示了某些材料存在的双牛顿区现象,并证明第一牛顿区的剪切黏度大于第二牛顿区的。
2.
A number of inventive methods have been developed for the measurement of interfacial shear viscosity.
综述测定界面剪切黏度的实验方法,重点介绍对其中几种常见实用的测定方法,包括这些测定方法各自的演变、测量原理、实验装置、灵敏度、优缺点等问题。
3.
The results showed that the apparent shear viscosity(ηa)and shear stress(τ)of all samples decreased with temperature increasing.
结果表明,随温度的升高,各试样的剪切黏度(ηa)和剪切应力(τ)下降;在250℃,剪切速率(γ)为200~10 000 s-1的条件下,各试样ηa和τ的差距逐渐缩小,流变曲线趋于重合。
4) shear bond strength
剪切结合强度
1.
Based on the PAGE equation and with the aid of light scattering coefficient technique,a new method to determine fiber-fiber shear bond strength was presented in this paper.
本文以PAGE方程为基础,结合光散射系数测量技术,并以针叶木为原料,研究了水分含量对纤维剪切结合强度和相对结合面积(Relative Bonded Area)RBA的影响。
2.
Based on the PAGE equation and with the aid of light scattering coefficient measuring technique,a new method for determining fiber-fiber shear bond strength was presented in this paper.
以PAGE方程为基础,结合光散射系数测量技术,提出了一种测量纤维间剪切结合强度的新方法,并以针叶木为原料,研究了打浆和湿压对纤维剪切结合强度和结合面积的影响。
5) shear bond strength
剪切粘结强度
1.
The shear bond strength of three different commercial luting cements to the ceramic material was evaluated.
置于37℃蒸馏水里保存24h后,进行剪切粘结强度测试。
2.
Objective: this in vitro study was firstly to evaluate the effect of two different bleaching regimens and two weeks post-time bonding on the shear bond strength of dentin to composite resin, and observe the dentin/composite interface of each group under scanning electron microscope.
目的:㈠通过用临床两种常用的漂白方法对离体牙进行漂白,采用即刻和延迟2周粘结树脂,分别测定牙本质和树脂剪切粘结强度,并用扫描电镜观察粘结界面超微形态,探讨漂白方法及漂白后粘结时间对牙本质粘结强度的影响,为临床上漂白后牙齿进行树脂粘结修复提供理论依据。
6) shear bonding strength
剪切固结强度
补充资料：黏结强度
分子式：
CAS号：
性质：使胶接头中的胶黏剂与被粘物发生破坏所需的应力，即破坏粘接头必要的单位黏合面积或单位长度的力。一般用规定形状和尺寸的试片，在一定的温度、湿度、速度条件下测定。破坏形式有拉伸、拉伸剪切、压缩剪切、劈裂、剥离、冲击、弯曲等。
CAS号：
性质：使胶接头中的胶黏剂与被粘物发生破坏所需的应力，即破坏粘接头必要的单位黏合面积或单位长度的力。一般用规定形状和尺寸的试片，在一定的温度、湿度、速度条件下测定。破坏形式有拉伸、拉伸剪切、压缩剪切、劈裂、剥离、冲击、弯曲等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条