1) interference
过盈
1.
The forces in joining the copper pipe to the aluminum radiator through interference fit are analyzed and calculated,and a new technique of pipe screwing and expanding is introduced so that the force of moving forward when the pipe is being expanded is reduced.
文章对热效率较高的铜铝复合散热片中铜管与铝型材散热片的过盈配合联接进行受力分析,并进行了必要的计算,同时提出了螺旋涨管新工艺,使涨管时所需要的进给力大大减小;对螺旋涨管机中关键部件涨管头的结构特点与工作原理进行了说明,对设计的螺旋涨管机工作原理与结构特点进行了详细叙述,同时也对整个螺旋涨管专机进行了简单介绍。
2.
This article analyzes the difference of the temperature between rudder bear installation and vessel sailing area;In this point of view, determination of the interference is deduced when coppery rudder bush is installed .
文章从舵承安装温度与船舶航区温度的差异这一角度入手进行了分析,推导出了铜质舵承安装过盈量的确定方法。
3.
For a high speed motorized spindle, the interference fit between the shaft and bearing has a great influence on the stiffness,rotary accuracy and life of the spindle.
高速电主轴轴承与转轴配合的过盈量大小对主轴的刚度、旋转精度和使用寿命具有十分重要的影响。
2) interference
过盈量
1.
The finite element method is applied to simulate the cold expanding of the joint as well as the bell and spigot fitting process of internal and external pipes, therefore to determine the interference and overlapping length, analyze the joint forces and give the uniform strength condition of joint and pipe.
文章针对D159mm×8mm无缝钢管进行了压接工艺条件下力学计算与分析,利用有限元方法模拟无缝钢管冷态下胀口和内外钢管承插配合过程,确定了内外钢管对接承插过盈量及搭接长度,分析了压接接头的受力情况,给出了压接接头与钢管等强的条件,为压接接头配合参数设计及工艺试验提供了依据。
2.
The analysis results show tha t the larger interference between the spindle and the toolholder or a higher draw bar force is benefit to improving th.
研究表明 ,适当提高过盈量 (轴向拉力 )对于提高主轴 /刀柄联接特性具有积极意
3) interference
光干涉
4) interference
干涉效应
1.
The interference among the same kind inclusions has been studied with the help of the digital holographic interferometry system.
利用自主开发的数字全息干涉测量系统针对同类型夹杂物间的干涉效应开展研究。
2.
For concentrated systems,there will appear interference to scattered intensities.
本文简要总结了目前文献中有关干涉效应的判断与处理方法。
5) interference
过盈值
1.
Shrinkage fit is a way to realize the tight joint through the interference between enveloping parts (hole) and enveloped parts (shaft).
过盈联接是以包容件(孔)和被包容件(轴)配合后的过盈值来达到紧固联接为目的。
2.
Based on the practice problem of sliding bearings interference measurement,a new method of non contact measurement is introduced,and explain some related problems including computer data acquisition,data processing and error processing,are explained.
针对轴瓦检验中实际问题 ,介绍了一种轴瓦过盈值无接触测量方法 ,并阐述了计算机数据采集、数据处理、人机界面、误差处理等相关软件设计问题。
6) interference
正向干扰
1.
The interference from matrix element indium could be eliminated by addition of appropriate EDTA (10%).
试验了采用原子荧光光谱法测定铟产品中锡时,以EDTA为络合剂掩蔽铟,利用EDTA与铟和锡形成络合物的稳定常数不同,克服基体铟对锡的正向干扰;优化了仪器测定条件,测定范围w(Sn)为0。
参考词条
补充资料：不盈
1.不满。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。