1) Mandarin HINT
![点击朗读](/dictall/images/read.gif)
噪声中言语测试
2) speech noise
![点击朗读](/dictall/images/read.gif)
语言噪声
3) noise test
![点击朗读](/dictall/images/read.gif)
噪声测试
1.
Based on the requirements of noise test of safety test standard on toys,the method of noise test and defined position of measurement point were described.
基于欧洲玩具安全标准中玩具噪声测试要求,按玩具类型对其噪声测试方法、测试点位置的确定进行论述,并对玩具噪声测试自动定位装置的机构设计、控制原理、硬件配置和应用进行重点的阐述,指出该定位装置解决了声响玩具噪声测量中测试点位置确定这个关键问题。
2.
In view of the environment characteristic of solid rocket motor ground ignition test and the former noise test system foundation, a new noise testing method of solid rocket motor ground ignition test is proposed.
针对固体火箭发动机地面点火试车试验的环境特点,在研究了以往固体火箭发动机噪声测试系统的基础上,提出了一种能够消除混响干扰的固体火箭发动机地面点火试车试验噪声测试方法。
5) noise measurement
![点击朗读](/dictall/images/read.gif)
噪声测试
1.
Secondly,research development of noise control is analyzed and theory research of noise radiation,noise measurement and noise resource diagnosis,CAE,research of numerical value and visual analysis,noise active control are .
接着,分析噪声控制工程的研究进展,提出噪声辐射理论研究,噪声测试与声源诊断,CAE、数值化与可视化研究,噪声的主动控制技术。
2.
The development techniques and applications of the virtual instrument for noise measurement & analysis on CY6140 engine lathe based upon NI LabVIEW 7 full development platform are briefly discussed.
介绍了基于NILabVIEW 7Express开发平台设计开发适于机电设备噪声测试虚拟仪器的实现技术及其在CY61 40普通车床噪声的测试实验 。
3.
To enhance the efficiency of noise measurement instrument and shorten the testing circles,a detailed configuration of the noise measurement hardware platform and a program of its relevant software are given.
为了提高噪声测试仪器使用效率,缩短测试周期,给出了一种噪声测试硬件平台的具体搭建方式及其配套软件的编写过程。
6) measuring noise
![点击朗读](/dictall/images/read.gif)
测试噪声
1.
Based on conception of IPV, a new damage detection method was proposed, and the measuring noise resistant ability of the proposed method was also analyzed theoretically.
利用白噪声激励下结构各测点的动力学响应之间的互相关函数,引入了内积向量(Inner Product Vector,IPV)的概念,提出了应用内积向量进行结构损伤检测的方法,并分析了测试噪声对基于内积向量的损伤检测方法的影响。
补充资料:测试结果可接受性的检查和最终测试结果的确定
测试结果可接受性的检查和最终测试结果的确定
check of the acceptability of test results and determination of the final test result
C凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。 在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。 可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。 按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条