1) thickness of periodontal ligament
牙周膜厚度
1.
Objective To assess the effect of the thickness of periodontal ligament on the fracture resistance of root and post-core system.
目的探讨不同牙周膜厚度对桩核-牙根联合体抗折力学性能的影响。
2) periodontal membrane
基牙牙周膜
1.
Three-dimensional finite element analysis of stress distribution about abutments periodontal membranes of separated removable partial denture and traditional removable partial denture;
分割式及普通可摘局部义齿基牙牙周膜的三维有限元分析
3) periodontal membrane
牙周膜
1.
Objective To study the microvascular bed of the periodontal membrane of the cat canine.
目的研究猫尖牙牙周膜微循环。
2.
METHODS Signal was elicited and processed from a tooth model imitated with human maxillary central incisor, silicone rubber periodontal membrane and resin alveolar bone, by utilizing FX 1 tooth mobility measurement system.
方法 以离体上颌中切牙为实验牙 ,硅橡胶模拟牙周膜 ,甲基丙烯酸甲酯模仿牙槽骨 ,用 FX- 1型牙动度测量系统采集、处理不同牙槽骨高度时的牙动度信号 。
4) Periodontium
[英][,periəu'dɔnʃəm] [美][,pɛrɪo'dɑnʃəm]
牙周膜
1.
The finite element analysis of the stress distribution in the periodontium of the mandibular incisors by use of multi-loop edgewise arch wire.;
多曲方丝对下颌中切牙牙周膜应力分布有限元分析
2.
Expression of insulin-like growth factor-Ⅰin periodontium during experimental tooth movement in rats;
大鼠正畸牙移动过程中胰岛素样生长因子-Ⅰ(IGF-Ⅰ)在牙周膜中的表达
3.
Objective:The aim of this study was to investigate, in a rat model, whether a state of hyper- or hypofunctional periodontium had an effect on the rate of bone remodeling induced by orthodontic treatment.
目的:通过检测不同牙周膜功能状态大鼠磨牙移动过程中压力侧牙槽骨表面破骨细胞计数及牙移动距离的差异,探讨牙周膜功能状态与牙槽骨改建的关系。
5) Periodontal ligament
牙周膜
1.
Three-dimensional stress analysis of periodontal ligament of mandible incisors fixed bridge abutments under dynamic loads by finite element method;
动态载荷下下前牙固定桥基牙牙周膜的三维有限元法分析
2.
Effects of mechanical stress on the secretion of TGF-β1 from human periodontal ligament fibroblasts;
机械压力对人牙周膜成纤维细胞TGF-β1蛋白表达的影响
3.
Three-dimensional stress analysis of the periodontal ligament of mandible incisors fixed bridge abutment under static loads by finite element method;
静态载荷下下前牙双端固定桥基牙牙周膜应力的三维有限元法分析
补充资料：湿膜厚度计
分子式：
CAS号：
性质：在漆膜制备后立即进行测量厚度的仪器。有轮规（wheel tube）和梳规（comb tube）。轮规由三个圆盘组成，外侧两个圆盘在某一半径处相切，该处的间隙为零，在相反关径处，间隔最大，外侧有刻度，指示不同间隙的读数；梳规为一正方形或矩形金属板或塑料片，在其4边都刻着带不同读数的齿，各齿距水平面有依次递升的不同间隙。湿膜厚度为沾湿的轮或齿的读数。
CAS号：
性质：在漆膜制备后立即进行测量厚度的仪器。有轮规（wheel tube）和梳规（comb tube）。轮规由三个圆盘组成，外侧两个圆盘在某一半径处相切，该处的间隙为零，在相反关径处，间隔最大，外侧有刻度，指示不同间隙的读数；梳规为一正方形或矩形金属板或塑料片，在其4边都刻着带不同读数的齿，各齿距水平面有依次递升的不同间隙。湿膜厚度为沾湿的轮或齿的读数。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条