1) Voidage
['vɔididʒ]
空洞率
1.
The new vacuum brazing equipment has perfectly resolved the problems of lack of capacity and voidage of traditional equipment,improving production efficiency and product quality greatly.
面对传统MCM基板生产设备的缺陷和产能的不足,开发了新型的真空钎焊设备,很好地解决了产能和空洞率的问题,使得生产效率和产品质量都有了极大的提高。
2) void content
空孔率,空洞率
3) hole
[英][həʊl] [美][hol]
洞空洞
4) Cavity
[英]['kævəti] [美]['kævətɪ]
空洞
1.
Analysis on formation cause of rutile crystal cavity;
金红石晶体空洞的成因分析
2.
Relationship of Cavity Formation and Active Pulmonary TB;
活动型肺结核患者血清血管内皮生长因子与空洞形成的关系
3.
Effects of the ground penetrating radar in probing arch bridge and cavity;
地质雷达应用于探测拱桥、空洞的效果验证
5) void
[英][vɔɪd] [美][vɔɪd]
空洞
1.
Effect of voids on the reliability of EBGA solder joints under thermal cycle;
热循环加载条件下空洞对EBGA焊点可靠性的影响
2.
Effects of rare earth on formation of voids at interface of aluminized coating/steel matrix and spalling resitance;
稀土对渗铝层/基体界面空洞生长和抗高温剥落性能的影响
3.
Formation Mechanism of BGA Void and Effects on Solder Joint Reliability;
BGA空洞形成的机理及对焊点可靠性的影响
6) cavitation
[英][,kævi'teiʃən] [美][,kævə'teʃən]
空洞
1.
The cavitation undet the superplastic tensile has been observed through the analysis of microstructure.
并通过对组织分析，观察在相应超塑性条件下空洞形成的基本特点。
2.
In this paper, a study of the cavitation of manganese-brass during superplastic deformation is reported.
对超塑变形后锰黄铜的空洞特征进行了系统研究。
3.
The residual strength and relation to the cavitation of as-warm rolledAl-Li-Cu-Mg-Zr alloy have been investigated after superplastic deformation under differ-ent tensile conditions.
研究了温轧态Al-Li-Cu-Mg-Zr合金经不同拉伸条件超塑变形后残余强度及其与空洞行为的关系结果表明在一定应变量范围内,以高的应变速率变形的试样比以低的应变速率变形的试样空洞少,残余强度高;在变形到较大的应变量时,先快后慢的两段速率拉伸变形与一段速率拉伸相比,试样中空洞少,残余强度高结合该合金变形初期发生的形变促使连续再结晶过程,讨论了拉伸条件与空洞行为及残余强度的关
补充资料：电导率(见电阻率)
电导率(见电阻率)
conductivity
d!日nd日O}已电导率(eonduetivity)见电阻率。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条