1) bearing stress/radial continous extrusion
挤压应力/径向连续挤压
2) continuous equal channel angular press
连续等径角挤压
1.
Ultra-fine grain copper prepared by continuous equal channel angular press;
连续等径角挤压制备超细晶铜
3) continuous extrusion
连续挤压
1.
Deformation model and stress distribution of continuous extrusion process;
连续挤压变形力学模型与接触应力分布规律
2.
Numerical simulation of temperature field of copper flat wire continuous extrusion forming;
铜扁线连续挤压过程温度场的数值模拟
3.
Analysis of temperature in copper continuous extrusion process;
铜连续挤压工艺过程中的温度分析
4) continuous extrusion forming
连续挤压
1.
Computer simulation of continuous extrusion forming process;
连续挤压成形过程的计算机仿真
2.
Using DEFORM-3D software and the rigid viscoplastic FE(finite element) theory,we study in some depth the effects of different spread outlets of a shoe on the continuous extrusion forming process of flat copper wire.
基于DEFORM3D软件,采用刚粘塑性有限元理论,运用三维有限元技术详细研究了不同靴座扩展出口宽度对铜扁线连续挤压成形过程的影响。
3.
The effects of the hindrance angles on continuous extrusion forming of the big flakiness copper flat wire are investigated by three-dimensional finite-element technology based on software DEFORM-3D.
基于DEFORM3D软件,采用刚粘塑性有限元理论,运用三维有限元技术详细研究不同阻碍角对铜扁线连续挤压成形过程的影响。
5) conform
[英][kən'fɔ:m] [美][kən'fɔrm]
连续挤压
1.
A Pressure Balance Criterion of Die Cavity Design in Cable Al Sheath CONFORM Cladding;
电缆铝护套连续挤压包覆型腔设计的均压判定准则
2.
Development of Management Information System in Research Center of CONFORM Engineering;
连续挤压工程研究中心管理信息系统的开发
3.
It provides theoretical basis for determining geometric Parameters of bonding container and designing die of conform.
从模具型腔结构特点上探讨了连续挤压制件裂纹产生的原因，利用主应力法和滑移法对焊合室内变形金属的应力进行了分析，为确定合理的连续挤压型腔几何参数和模具设计提供了一定的理论依据。
6) radial extrusion
径向挤压
1.
Technical Study of Radial Extrusion Forming on the Super-Long Odd Shafts based on Multiple Directions Extrusion
基于多向挤压的超长异形轴径向挤压工艺研究
2.
The radial extrusion technological process of the internal thread spline was studied and a set of extrusion mould suitable for the forming of the internal thread spline in the guide bush.
以汽车单向器导向筒内螺旋花键为研制对象 ,对内螺旋花键的径向挤压工艺进行了研究 ,设计了1副适合于导向筒内螺旋花键径向成形的挤压模。
3.
The warm radial extrusion of internal ring with inclined groove is introduced in this paper.
介绍了斜槽内环零件的温径向挤压工艺及三瓣模的设计、模具结构及主要零件的设计及选材。
补充资料：工资挤压
工资挤压：指不同经历和不同表现的员工间的工薪差别变得很小这一状况。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条