1) coagulating temperature
凝胶浴温
1.
Only when the miscibility ofpolymers is better,a blended UF membrane with greatly improved flux orretention rate will be obtained by raising coagulating temperature or byadding a small amount of NaCl without excessive damage of other prope-rties.
虽然凝胶浴温提高都使膜的透水率提高而截留率下降,但相容性好可在截留率下降较小的情况下较大地提高透水率;利用少量NaCl 对凝胶浴的添加,也只有在相容性好时才能在不降低透水率的情况下有效改善截留率;蒸发时间的影响也因相容性不同而异,但延长蒸发时间并不可取。
2) gel-bath temperature
凝胶浴温度
1.
The effect of PPENK concentration,additive content,air gap distance,gel-bath temperature and fiber thickness during the membrane prepared process on the structure and property of PPENK hollow fiber ultrafiltration membranes were studied.
考察了聚合物浓度、添加剂含量以及纺丝过程中空气间隙、凝胶浴温度和纤维壁厚对膜结构及性能的影响。
3) coagulation bath
凝胶浴
1.
Porous poly(vinylidene fluoride)(PVDF) membranes were prepared by phase inversion method in pure water and ethanol/water coagulation baths of φ(ethanol)=20% and φ(ethanol)=40%,and these membranes were studied by SEM and DSC.
利用倒相法在纯水和φ(ethano l)=20%、φ(ethano l)=40%的乙醇/水凝胶浴中分别制备了聚偏氟乙烯(PVDF)多孔膜,通过SEM,DSC对这些薄膜进行了分析表征。
2.
The effects of different solvent concentrations in coagulation bath,coagulation temperatures and different solvent concentration in core solution on PVDF/PVC blend membranes performance were studied and discussed in this paper.
采用干-湿相转化法制备PVDF/PVC共混中空纤维膜,通过对水通量、孔隙率、平均孔径的测试及扫描电镜的微观分析,讨论了凝胶浴组成、温度和芯液浓度对PVDF/PVC中空纤维膜性能及结构的影响,并进行了详细的理论分析。
4) External bath gel
外凝胶浴
5) coagulation temperature
凝固浴温度
1.
Structure and property of Ionicell fiber dependent on coagulation temperature
凝固浴温度对Ionicell纤维结构及性能的影响
6) gelation temperature
胶凝温度
1.
The aim of the present work is to investigate the characteristics including gelation temperature, sol-gel transition temperature (T_ s-g ), gel strength, stable viscosity, erosion and drug release behavior of the thermosensitive in situ gel which are composed o.
本文以泊罗沙姆Pluronic F127为温度敏感原位凝胶材料,考察了PluronicF127与Pluronic F68不同浓度处方对地塞米松磷酸钠温度敏感原位凝胶的胶凝温度、相转变温度、凝胶强度、稳态黏度、溶蚀和药物释放行为等特性的影响。
2.
The experimental results show that the gelation temperature at which G'= G", coincides with the gel point when the temperatu.
5-1℃/min,储能模量(G’)和耗能模量(C”)相等时的胶凝温度与按SY/T0541-94方法测定凝点基本一致,说明用小振幅振荡剪切温度扫描法来确定含蜡原油的凝点是可行的。
3.
The gelation extent and structure strength can be revealed by the viscoelastic parameters and gelation temperature measured by small amplitude oscillatory shear experiment.
结果表明,储能模量和耗能模量随测量温度的降低呈指数规律增加;存在使流变性恶化的“最差加热温度”;降温速率越高,测量温度下蜡晶结构强度和胶凝温度越低。
补充资料：Sds-聚丙烯酰胺凝胶电泳凝胶电泳
sds-聚丙烯酰胺凝胶电泳（sds-page，sodium dodecyl sulfate-polyacrylamide gel electrohoresis）
在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的，而不是根据分子所带的电荷和大小分离的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条