说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 倾斜偏心环空
1)  inclined eccentric annulus
倾斜偏心环空
1.
The analytical expressions for the apparent viscosity and velocity distribution of thelaminar helical flow of Bingham fluid in the inclined eccentric annulus have been derivedbased on the fundamentals of Non-Newtonian fluid mechanics and geometric characteris-tics of eccentric annulus in directional well.
根据非牛顿流体力学基本原理及定向井偏心环空的几何特点,导出了倾斜偏心环空中Bingham流体层流螺旋流流场视粘度函数、速度函数的解析表达式。
2)  oblique misalignment
倾斜偏心
1.
Effects of oblique misalignment in a coaxial waveguide TEM modes performance
倾斜偏心对同轴波导TEM模式性能的影响
3)  Decentration and tilt
倾斜和偏心
4)  decenter and tilt
偏心与倾斜
5)  eccentric and inclined loads
倾斜偏心荷载
1.
Analysis of single piles under eccentric and inclined loads in layered soils;
成层地基中倾斜偏心荷载下单桩计算分析
2.
The behavior of piles in layered clays under eccentric and inclined loads can not be analyzed by traditional finite pole element method if P-Δ effect is significant.
传统有限杆单元法不能考虑倾斜偏心荷载下基桩的P-Δ效应,假定桩身位移为三次幂函数,结合倾斜偏心荷载下单桩受力微分方程确定的桩身弯矩、剪力与桩身水平位移关系,导得具有简洁形式、计入P-Δ效应的杆单元刚度方程,进而得到改进的有限杆单元方法,并给列出了用该法进行成层地基中倾斜偏心荷载、桩自重、水平分布荷载、竖向分布荷载和竖向分散集中荷载综合作用下并考虑桩身倾斜影响基桩内力位移分析的具体计算步骤。
6)  tilt and off-center element
倾斜偏心元件
补充资料:在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.

1)连接PA,PB. A(-100,0,0) B(100,0,0)



图1



在当前坐标下:


2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;


3)连接CD;


4)以CD为直径画圆;


5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;


6)过O作CD的垂线,交圆于E,F;



图2



7)用三点UCS命令,取三点为:O,P,C;


8)过点O作PO的垂线GO,交PC于G;



图3



9)再次用三点UCS命令,取三点为O,F,G;


10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;



图4



11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.


12)删除辅助线条.



图5

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条