1) identical load slntering
均压烧结
2) uniform sintering
均质烧结
1.
Point at the problems presented in MPS process, the uniform sintering technology was applied to perfect the MPS process in SHUIYE I & S Co As a result, the quality and quantity of sinter were increased and the fuel consumption was decrease
针对安钢集团水冶钢铁有限公司小球团烧结生产中存在的问题 ,采用均质烧结技术对其进行完善 ,取得了产质量提高 ,燃耗降低的良好效
2.
The uniform sintering process required that the exchang of material and energy always at the balance state,so the product was also uniform.
均质烧结要求烧结过程中的物质交换、能量交换 (包括交换的物质品种、数量、速度、位置 )始终处于均一状态 ,其产品必然也是均质的。
3) steady sintering
均匀烧结
1.
in this paper, the stabilities of air-kinettics schedule,thermal schedul and operation schedul were selected as criteria to identify steady degree of sintering process,and the restraint factors of steady sintering was also analyzed.
本文采用烧结过程气体动力学制度、热工制度及作业制度的稳定性来衡量烧结过程的均匀性；分析了均匀烧结的制约因素，探讨了实际生产条件，提出了从纵向、横向和竖向全方位实现均匀烧结的途径。
4) homogenized sintering
均化烧结
5) Pressureless Sintering
无压烧结
1.
Preparation process of ZrB_2/B_4C ceramic composites by pressureless sintering based on mechanical mixing;
基于机械混合法无压烧结制备ZrB_2/B_4C陶瓷复合材料
2.
Research on pressureless sintering of hexagonal boron nitride;
六方氮化硼无压烧结研究
3.
Discussion on pressureless sintering of SiC ceramic;
SiC陶瓷无压烧结工艺探讨
6) hot-press sintering
热压烧结
1.
Research on hot-press sintering process of N type thermoelectric materials ZnO;
N型热电材料ZnO热压烧结工艺研究
2.
Si_3N_4 ceramics were prepared by aligning theα-Si_3N_4 whisker in the substrate via tape casting and hot-press sintering.
利用流延成型使α-Si_3N_4晶须在基体中定向排列,并采用热压烧结技术制备了Si_3N_4陶瓷。
3.
Ti_3Al/TiC+ZrO_2 composites were prepared by mechanical alloying and hot-press sintering.
采用机械合金化和热压烧结制备了Ti3Al/TiC+ZrO2复合材料。
补充资料：冷压烧结成型
分子式：
CAS号：
性质：又称冷塑法，塑料材料加工方法之一。即将冷塑材料或无机可塑塑料加入到模具中在高压下经过一定时间成型。取出型坯后再加热后冷却使其硬化或不加热而经化学反应固化得到制品。此法操作简单、迅速，如超高分子量及酚醛树脂的塑料制品常采用此法加工。
CAS号：
性质：又称冷塑法，塑料材料加工方法之一。即将冷塑材料或无机可塑塑料加入到模具中在高压下经过一定时间成型。取出型坯后再加热后冷却使其硬化或不加热而经化学反应固化得到制品。此法操作简单、迅速，如超高分子量及酚醛树脂的塑料制品常采用此法加工。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条