1) strength of brazed joints in shear
接头抗剪切强度
2) joint shear strength
接头剪切强度
1.
Influences of the metallizing technologic conditions, Ni plating and subsequent annealing on the joint shear strength were investigated.
考察了金属化工艺、镀镍及镀后热处理对接头剪切强度和钎焊效果的影响。
3) shear bond strength
粘接抗剪切强度
1.
In this study , we bonded resin orthodontic brackets to two kind of commonly - used prosthodontic materials: porcelain and light - cured composite resin with domestic adhesive, ordinary light - cured composite resin and BISCO ORTHO - ONE~? orthodontic Direct Bonding System respectively and then the shear bond strength of the re.
本实验通过使用不同的粘接剂粘接树脂托槽与经过不同方式表面处理的瓷和光固化复合树脂修复材料,对其粘接抗剪切强度,影响树脂托槽与修复材料直接粘接的因素以及去粘接后原修复面的完整性进行实验研究。
2.
In this study, we bonded metal orthodontic brackets to two kinds of commonly-used prosthodontic materials: porcelain and light-cured composite resin with domestic adhesive and ordinary light-cured composite resin respectively and then the shear bond strength of the metal brackets, the integrity of the prosthodontic surface after debonding and the microsco.
本研究使用国产的粘合剂和普通光固化复合树脂粘接金属托槽与瓷、光固化复合树脂两种常用的修复材料，并对其粘接抗剪切强度，去粘接后原修复面的完整性，表面处理后修复面的显微形态结构进行了实验研究。
4) shear strength of joint
接头抗剪强度
1.
Effect of Ni on wettability and shear strength of joints of Ag20CuZnSnP filler metal;
镍对Ag20CuZnSnP钎料铺展润湿性和接头抗剪强度的影响
5) shear strength
抗剪切强度
1.
The effect of crystal powder on the shear strength and expansion ratio of the crystal powder/epoxy resin composite by different composition and technology was studied systematically.
对水晶粉/环氧树脂复合材料的抗剪切强度、热膨胀系数进行较系统的研究,并用扫描电镜(SEM)对水晶粉/环氧树脂复合材料断面显微结构进行了观察。
2.
Gauging the shear strength,tensile strength and modulus,glass transition temperature of the composite and their change during the aging test.
选用TDE-85和E-51作为主体树脂,制备了一种T700碳纤维复合材料,并对这种复合材料进行耐湿热老化研究,分别测定其抗剪切强度、抗拉伸强度及模量和玻璃化转变温度随老化时间的变化值。
3.
This paper briefly introduces the use of the cable bolt anchoring technology, initially analyzes the anchoring mechanism of the fully bonded cable bolt in the jointed rock mass, and examines some factors affecting the tensile bond strength and the shear strength of the cable bolt in the jointed rock mass.
简要介绍了锚索加固技术的应用，并对全长粘结式锚索在节理岩体中的锚固作用机理进行初步分析，同时对节理岩体中锚索加固的抗拉粘结强度及抗剪切强度的影响因素进行了分析。
6) shear bond strength
抗剪切强度
1.
Comparison on shear bond strength of edgewise brackets bonding with three orthodontic adhensives under different adhensive conditions;
3种正畸秞质粘接剂在不同粘接条件下的抗剪切强度比较
2.
Objective To observe the shear bond strength after different methods are adopted to deal with the enamel with fluoride.
方法挑选因正畸需要而拔除的96颗双尖牙,随机分为对照组、酸蚀前加氟组、酸蚀液中加氟组、酸蚀后加氟组,粘接托槽后进行冷热循环实验,测定并记录托槽抗剪切强度及黏接剂残留指数计分评估。
3.
Result:The shear bond strengths were negative relative to the roughnes.
各组处理后涂底涂剂,与硅橡胶粘结,测试其抗剪切强度,观察其破坏方式。
补充资料：层间剪切强度
分子式：
CAS号：
性质：层压件和纤维增强复合材料中层与层之间的最大剪切强度。作用于面上的应力与面相平行。其值较小。如树脂为环氧体系，增强材料为玻璃纤维时，纤维方向的拉伸强度达103MPa，而层间剪切强度为40～50MPa。
CAS号：
性质：层压件和纤维增强复合材料中层与层之间的最大剪切强度。作用于面上的应力与面相平行。其值较小。如树脂为环氧体系，增强材料为玻璃纤维时，纤维方向的拉伸强度达103MPa，而层间剪切强度为40～50MPa。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条