1) light beam surface hardening
光束表面淬火
2) Laser Surface Quenching
激光表面淬火
1.
The simulation of the temperature field associated with laser surface quenching is discussed using finite element analysis software ANSYS.
基于有限元分析软件ANSYS对激光表面淬火温度场进行模拟,并结合实验的数据,建立了材料表面能量转换系数的变化规律的数学模型。
2.
A set of technological specifications fit for laser surface quenching have been obtained in view of the punching die of T12 steel lamp holder through heat tr-eatment, metallographies analysis and industrial application etc.
针对T_(12)钢灯头冲孔凹模,经过热处理、金相分析检测、工业应用等试验过程,研究总结出一套适于激光表面淬火的工艺规范,使该模具工作寿命平均提高近3倍。
3) laser surface hardening
激光表面淬火
1.
Study of laser surface hardening engineer testing on the local of steam turbine lamina;
汽轮机叶片局部激光表面淬火工艺试验研究
2.
Investigation of laser surface hardening for mould-cutting roller;
模切辊激光表面淬火的研究
3.
The laser surface hardening for cutting fibre roller made of 4Cr13 stainless steel was tested by using continuous wave CO 2 laser beam.
用连续波CO2 激光束对 4Cr13不锈钢过丝辊进行激光表面淬火。
4) surface hardening
表面淬火
1.
The Study of Control System for Plasma Surface Hardening;
等离子表面淬火控制系统的开发研究
2.
Study of Technological Test on the Plasma Arc Surface Hardening Technology;
等离子弧表面淬火工艺试验研究
3.
The results such as hardness,depth and microstructure of surface hardening were studied when the elements such as power,velocity,diameter,length of plasma arc were changed.
以 45钢为典型材料 ,进行了等离子弧表面淬火技术工艺试验研究。
5) Surface quenching
表面淬火
1.
The surface quenching for crane wheel by air resistance furnace heating;
起重机车轮的空气电阻炉加热表面淬火
2.
The depth of hardened layer after surface quenching was about 0.
磨辊齿经等离子弧表面淬火后硬化层的厚度约为0。
3.
The surface quenching process parameter of the finished cold rolling roll made of semi-high speed steel has been described in this article.
研究了半高速钢成品冷轧辊的表面淬火工艺参数。
6) wide-band laser surface quenched
宽带激光表面淬火
1.
Microstructure, microhardness and tribological properties of ferrous sintered cam materials were investigated under two state (sintered and wide-band laser surface quenched).
本论文研究了铁基烧结凸轮材料经宽带激光表面淬火前后的显微组织、硬度及其摩擦学特性。
补充资料：表面淬火
分子式：
CAS号：
性质：将工件表面迅速加热到淬火温度后进行淬火，使工件表面层淬硬到一定深度，而心部仍保持未淬火状态的一种热处理工艺。经表面淬火的工件，其表面硬度、耐磨性和疲劳强度均高，而心部则保留一定的塑性和韧性。表面淬火常用方法有火焰表面淬火、高频表面淬火和中频表面淬火等。
CAS号：
性质：将工件表面迅速加热到淬火温度后进行淬火，使工件表面层淬硬到一定深度，而心部仍保持未淬火状态的一种热处理工艺。经表面淬火的工件，其表面硬度、耐磨性和疲劳强度均高，而心部则保留一定的塑性和韧性。表面淬火常用方法有火焰表面淬火、高频表面淬火和中频表面淬火等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条