1) parison tube
坯管
1.
The paper introduces the structure and design characteristics of the heat runner injection mold for one kind of beverage bottle parison tube.
介绍了一种饮料瓶坯管热流通注射模的结构及设计特点。
2) tube billet
管坯
1.
The forming limit of forward extrusion and cross rolling tube billet;
管坯正挤—横轧的成形极限
2.
Uniformity of heat flux on tube billets heated in ring oven;
环形加热炉内管坯辐射热流均匀性的分析
3.
The relations between the dimension of tube billets and the shape of finished products were investigated and compared with the computational results.
以铅管为材料,对钎钢的轧制过程进行了试验研究,分析了轧制工艺参数及管坯尺寸对成品外形的影响,并与数值模拟结果进行了对比,两者吻合较好,从而验证了钎钢轧制过程模拟结果的正确性和可靠性,为确定合理的轧制工艺参数提供了理论依据。
3) Tube Blank
管坯
1.
Practice of Steelmaking Process for of N80 Grade Steel 36Mn2V for Oil well Tube Blank;
油井用N80级36Mn2V非调质钢管坯的冶炼工艺实践
2.
The production flow,after forged heat treatment and final heat treatment process for the high strength tube blank have been described in this article.
介绍了高强度管坯的生产流程及锻后热处理、最终热处理工艺。
3.
This paper introduces practice on producing quality carbon steel for seamless tube blank with LD-LF process in Hangzhou Iron & Steel Group Company.
介绍了应用转炉加LF精炼生产合格的优质碳素管坯钢的情况。
4) tubular
[英]['tju:bjələ(r)] [美]['tubjəlɚ]
管坯
1.
Closed loop control of spray height in tubular preparation with reciprocating spray deposition process;
往复式喷射沉积管坯制备中喷射高度的闭环控制
2.
Deposition behavior and movement parameters optimization for reciprocating spray forming tubular;
往复式喷射成形管坯沉积特性及运动参数优化
3.
Process principle of reciprocating spray forming large thick-wall tubular was analyzed.
介绍了基底往复式喷射成形制备大壁厚管坯的工艺原理,并对雾化锥流率的空间分布和单层沉积轨迹进行了研究,在此基础上建立了单层沉积的数学模型。
5) pipe blank
管坯
1.
To insure the spinning temperature,the interspace of pipe blank and mold is less than or equal to 0.
要确保旋压温度,管坯的长度在成品倍尺内取短倍尺,管坯内径与芯模之间的间隙不大于0。
6) tube
[英][tju:b] [美][tub]
管坯
1.
7Si alloy tubes are prepared by multi-layer spray deposition.
7Si耐热铝合金管坯 ,冷却速度高 ,组织细小 ,且壁厚增加对组织影响不大 ;多层喷射沉积耐热铝合金管坯挤压后室温强度 σb 可达 445MPa ,350℃高温强度σb 达1 95MPa ,远高于Osprey工艺制备的同类材料制品。
2.
Through expermental investigations of tube central-upsetting, it is revealed that four typical modes of defor-mation in the inner wall-straight wall.
通过管坯中部镦锻的实验研究，观察到带芯轴支撑的管坯发生塑性变形时，其内壁沿轴向呈现四种典型的几何形状：直壁、单鼓形、多鼓形和折叠。
3.
On the inner wall surface through the cracks of large thick-walled tube for chemical composition analysis,hardness,mechanical testing,metallography inspection and analysis.
采用化学成分分析、硬度测定、力学性能测试、金相检验及综合分析等方法对内壁表面出现裂纹的大型厚壁管坯进行了分析。
补充资料：天津钢管公司管坯在250连轧管机组的穿孔机上穿孔
天津钢管公司管坯在250连轧管机组的穿孔机上穿孔
天津钢管公司管坯在250连轧管机组的穿孔机上穿孔
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条