1) pressure vessel steel plates
压力容器钢板
1.
The lot production of a series of low temperature pressure vessel steel plates such as 16MnR,16MnDR and 09Mn2VDR successfully developed by Chongqing Iron and Steel Co.
介绍了重用应用微ｖ，Ｔｉ处理技术，成功开发并批量生产系列低温压力容器钢板１６ＭｎＲ，１６ＭｎＤＲ，０９Ｍｎ２ＶＤＲ的情况，说明了上述３个品种的冶炼、轧制工艺和相关参数以及良好的力学（特别是低温冲击）性能和社会、经济效益。
3) pressure vessel steel
压力容器钢
1.
Progress of study on pressure vessel steels manufactured by unquenched tempered micro-alloying technology;
微合金非调质压力容器钢的研究进展
2.
A small sample method for testing the fatigue crack growth rate curve of pressure vessel steel;
压力容器钢疲劳裂纹扩展速率曲线测试的小样本方法
3.
In order to study the cleanliness of pressure vessel steel 12Cr1MoVG produced by EAF-LF/VD-CC route at Tianjin Pipe Company Ltd.
为了解天津钢管集团公司EAF-LF/VD-CC工艺生产压力容器钢12Cr1MoVG的洁净度水平,通过系统取样、示踪剂追踪、综合分析等方法,对LF处理前后、中间包钢水和连铸坯中总氧、显微夹杂及大型夹杂物的数量及变化情况进行了全面研究。
4) steel pressure vessel
钢制压力容器
1.
Reliability prediction of corrosion residual life of steel pressure vessel and pipeline;
钢制压力容器与管道腐蚀剩余寿命可靠性预测
2.
Fuzzy reliability theory of determining testing pressure of steel pressure vessels;
钢制压力容器试验压力的模糊可靠性理论
3.
With stress releasing method, the heat residual weld stress has been tested in steel pressure vessel.
应用小孔释放法对系列钢制压力容器手弧焊接接头的焊接残余应力进行测试 ,讨论了焊接残余应力的分布规律及其相关影响因素 ,对加载法消除焊接残余应力的效果进行了初步的验证。
5) steel pressure container
钢制压力容器
1.
n the paper, the purpose and meaning of making the evaluating standard of JB4708 92 steel pressure container and the meaning of some technical terms had been explained further, the executive method of standard had been more clearly illustrated by using formation style, it has a benefit to understand and implement for the profession personnels.
本文对制定ＪＢ４７０８—９２钢制压力容器焊接工艺评定标准的目的意义和某些技术术语的含义作了进一步的解释，采用表格型式更清楚地说明了标准的执行方法，有助于行业人员去理解和贯
2.
The AE singals performances in the small sized steel pressure container examination were introduced,the small sized steel pressure container s AE computer examing system is set up.
介绍了AE信号在小型钢制压力容器检测中的应用 ,建立了钢制压力容器声发射计算机检测系统 ,并试验分析了两种不同状态下钢制容器的AE信号时域波形 。
6) steel pressure vessels
钢制压力容器
1.
in this paper, on the basis of the elastic-plastic theory an analysis of the risidual stress in the cylinder of steel pressure vessels which is generated when the steel plate was made into a cylinder is given.
应用弹塑性理论分析了钢制压力容器简体在制造成型时产生的残余应力，指出按中径公式设计时不应忽视残余应力，建议将简体由四周向水压试验应力控制在０。
2.
This paper,on the basis of the imcremental theory of Plasticity, analyses the stress and strain caused in the cylinder of steel pressure vessels when the steel plate is made into a cylinder.
采用塑性力学的增量理论分析了钢制压力容器简体在用钢板有卷成形时产生的应力与应变。
补充资料：压力容器用钢板
分子式：
CAS号：
性质：压力容器用钢板是专门生产一般压力容器、使用温度在-20℃以下的低温压力容器和多层式高压容器外壳用的厚板。钢种除3号普通钢外，主要是低合金结构钢，代号中用R(容器)、DR(低温容器)和gC(高压多层)表示。多层式高压容器用钢板只供应6mm一种厚度的，低温压力容器钢板的厚度为6～40mm，一般压力容器钢板的品种在普通厚板(6～60mm)和特厚板(>60～115mm)的范围内。
CAS号：
性质：压力容器用钢板是专门生产一般压力容器、使用温度在-20℃以下的低温压力容器和多层式高压容器外壳用的厚板。钢种除3号普通钢外，主要是低合金结构钢，代号中用R(容器)、DR(低温容器)和gC(高压多层)表示。多层式高压容器用钢板只供应6mm一种厚度的，低温压力容器钢板的厚度为6～40mm，一般压力容器钢板的品种在普通厚板(6～60mm)和特厚板(>60～115mm)的范围内。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条