1) osmotic acrylic resin
渗透型丙烯酸树脂
1.
The synthetic process of osmotic acrylic resin and the factors influencing the yield of the resin were discussed.
报道了渗透型丙烯酸树脂的合成过程与结构表征，探讨了合成反应中影响产率的因素。
2) acrylate resin
丙烯酸树脂
1.
Study on Synthesis of Waterborne Acrylate Resin and Their Modification;
水性丙烯酸树脂的合成及其改性的研究
2.
Environment friendly acrylate resin was prepared and applied in antifouling coating.
探讨环境友好型防污涂料的基料丙烯酸树脂的合成及其在海洋防污涂料中的应用。
3.
The acrylate resin used for holographic coating for creating imaging directly on printed paper surface was prepared.
研究探讨了一种适用于全息图文模压复制涂料的丙烯酸树脂的合成工艺。
3) acrylic resin
丙烯酸树脂
1.
Technical analysis and solving of abnormal occurrences in the production of acrylic resin;
丙烯酸树脂生产异常现象的技术分析及处理
2.
Research on synthesis of water-soluble acrylic resin;
水性丙烯酸树脂的合成研究
3.
Study on the environment-protection electrical steel insulating coatings of semi-inorganic acrylic resin;
环保半无机丙烯酸树脂型电工钢绝缘涂料的研究
4) acrylic acid resin
丙烯酸树脂
1.
Application of phenolic resin on the improving flame retardancy of acrylic acid resin
酚醛在丙烯酸树脂防火改性中的应用
2.
The emulsion polymerization process of enteric acrylic acid resin was studied.
采用乳液聚合法制备肠溶型药物包衣用丙烯酸树脂,采用甲基丙烯酸与甲基丙烯酸甲酯作为共聚单体、过硫酸钾作为引发剂、十二烷基硫酸钠及OP-10复配作为乳化剂、苯乙烯的二聚体作为分子量调节剂、碳酸氢钠作为pH值调节剂,考察了乳化剂配比及用量、引发剂及分子量调节剂的用量、反应温度、加料方式、相比等因素的影响,最终确定了实验制备药物包衣用丙烯酸树脂的最佳条件。
3.
Introduced the synthetic technology and approach of water-soluble and emulsion acrylic acid resin, summarized the development and application of water-borne acrylic acid resin in water-based ink, and pointed out some views of its development.
介绍了水溶型丙烯酸树脂和乳液型丙烯酸树脂的合成工艺和方法,阐述了水性丙烯酸树脂的研究进展及其在水性油墨中的应用情况,指出了油墨用水性丙烯酸树脂的发展趋势。
5) Eudragit
丙烯酸树脂
1.
METHODS 4-ASA-Na colon-specific targeting release coated tablets were prepared by a sugar coater,using the acrylic resin Eudragit RL-RS and Eudragit FS as coating polymers,and triethyl citrate as plasticizer.
方法:以渗透型丙烯酸树脂EudragitRL与EudragitRS混和包衣液作为内层缓释层,pH依赖型丙烯酸树脂EudragitFS作为外层肠溶层,以柠檬酸三乙酯作为增塑剂,使用可调速糖衣机包衣,并研究包衣片在模拟人体胃肠道环境中的释放情况。
2.
Results A satisfactory 24 h -sustained release curve can be obtained when the pellets is coated with Eudragit RL30D and RS30D under the optimized formulation and preparing conditions.
结果以丙烯酸树脂EudragitRL30D和EudragitRS30D为包衣材料,质量比为4∶1,包衣增重10 % (w) ,增塑剂的用量为2 0 % (w ) ,无需熟化,可满足2 4h缓释的要求。
3.
Eudragit dispersions were coated as a sustained-release layer in a fluid-bed equipment .
方法采用离心造粒技术制备阿昔洛韦素丸,在流化床内采用丙烯酸树脂水分散体对其包衣,制备阿昔洛韦缓释微丸。
6) acrylic resins
丙烯酸树脂
1.
This paper presents a comprehensive introduction about the developing conditions and virtues of solventborne acrylic resins,the latest development of which products has been described in detail.
本文介绍了溶剂型丙烯酸树脂的发展情况及其特点,详细论述了溶剂型丙烯酸树脂的品种发展现状。
2.
A series of acrylic resins were synthesized by using ditertiary butyl peroxide (DTBP) as a free radical initiator and 2-mercaptoethanol as a chain transfer agent.
以过氧化二叔丁基为自由基引发剂、巯基乙醇为链转移剂,合成了高固体分、低粘度的羟基丙烯酸树脂,其粘度在1000mPa·s以下,固体分高达65%～70%。
3.
This paper describes the approach to prepare the thermosetting acrylic resins for plastic aluminium compounding plate, especially discusses the selection of monomer, the relative molecular weight, reaction ratio of feedstock and the loading determination of butyl alcohol.
本文阐述了铝塑复合板用热固性羟基丙烯酸树脂的制备过程,着重讨论了单体的选择,环氧树脂相对分子质量和接入比例的确定及丁醇量的确定。
补充资料：丙烯酸-丙烯酸甲酯-丙烯酸羟丙酯共聚物
分子式：
分子量：
CAS号：55719-33-0
性质：
分子量：
CAS号：55719-33-0
性质：
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条