说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 预聚合反应
1)  Prepolymerization
预聚合反应
1.
The prepolymerization with Ti-Mg Catalyst and the influence of products of prepolymerization on the gas-phase polymerization of ethylene are reported.
研究了用镁粉研制的Ti-Mg系乙烯气相聚合催化剂在各种条件下的预聚合反应,以及各种类型AlR_3对预聚合反应的影响。
2)  prepolymerization reaction
预聚反应
1.
A kind of waterborn polyurethane is synthesized by the reaction of diisocyanate with polyethylene glycol at the presence of end capping reagent;The factors that affect the blocking reaction and prepolymerization reaction were investigated.
以二异氰酸酯、聚醚多元醇为原料,利用二异氰酸酯和聚乙二醇在封端剂的存在下合成了一种水性聚氨酯;探讨了影响预聚反应和封端反应的因素。
2.
The influence of reaction temperature, used solvents and catalysts on the prepolymerization reaction was investigated.
研究了反应温度、溶剂、催化剂及用量对预聚反应的影响。
3.
The results indicated that the optimum reaction temperature of prepolymerization reaction was 75℃,the maximum reaction temperature of prepolymer was between 60℃ and 80℃,the quantity of hydrophilic chain extender was equal to 5% of feedstocks.
以甲苯二异氰酸酯(HDI)、聚酯多元醇和二羟甲基丙酸(DMPA)为主要原料合成水性聚氨酯固色剂,研究了反应温度、聚酯多元醇、有机溶剂、亲水扩链剂等对预聚反应的影响。
3)  prepolymerization
预聚反应
1.
Research of reaction conditions on prepolymerization of polyester anionic waterborne polyurethane emulsion;
阴离子水性聚酯聚氨酯乳液预聚反应条件的研究
4)  prepolymerization kinetics
预聚合反应动力学
1.
Bulk polymerization of ABS resin Ⅱ.Study on prepolymerization kinetics
本体法合成ABS树脂 Ⅱ.预聚合反应动力学研究
5)  Polymerization [英][,pɔlimərai'zeiʃən]  [美][,pɑlɪməraɪ'zeʃən]
聚合反应
1.
Application of Room Temperature Ionic Liquids in Polymerization;
室温离子液体在聚合反应中的应用
2.
Influences of the using amount of emulsifier and stirring condition on the particle size in heterogeneous polymerization system;
非均相聚合反应中乳化剂用量及搅拌状况对粒径大小的影响
3.
Study on the Surfactant Used in Polymerization in Supercritical Carbon Dioxide;
在超临界CO_2聚合反应中应用的表面活性剂的研究
6)  polymerization reaction
聚合反应
1.
The effect of micro amount water on the polymerization reaction of cis-1,4-polybutadiene rubber;
微量水对顺丁橡胶聚合反应的影响
2.
Progress of butyl rubber production status and polymerization reaction was summarized.
综述了国内外丁基橡胶生产现状及其聚合反应技术进展,对聚合反应器的类型、结构特点以及聚合反应引发体系进行了介绍。
3.
The impact of catalyst activity on polymerization reaction and product quality is discussed and improvement measures are proposed.
文章分析了M型钛系催化剂的反应机理及影响催化剂活性的因素,并结合生产实际讨论了催化剂活性对聚合反应及产品质量的影响,进而提出了改良措施。
补充资料:设备安装前的准备工作——设备的预装配与预调整
设备安装前的准备工作——设备的预装配与预调整
 
文章编辑:moji
文章来源:
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条