说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 2300四辊轧机
1)  2300 four-high mill
2300四辊轧机
1.
Based on the equipment features and process state of rolling products, a computer simulating program for roll shape of support roll in 2300 four-high mill is developed, which can be used within a large range of width of rolling products.
根据2300中板轧机的设备特点、轧制产品的工艺状况,开发了一个能适应轧件宽度变化范围较大的2300四辊轧机支撑辊辊型的计算机仿真程序,并研制了一种新的2300四辊轧机支撑辊辊型曲线,以提高该轧机的板形控制能力。
2)  4-h mill
四辊轧机
1.
Modelling study of the elastic deformation for 4-h mill;
四辊轧机弹性变形解析模型的研究
2.
This paper was to discuss the elastic deformation of rollers and interaction between work rollers and the strip during the roller milling process of a 4-h mill,by analyzing stress and deformation of rollers,put forwards a concise and practicable mathematic model of roller gap's shape,which resulted from some relevant factors,such as rolling pressure,bending force and so on.
针对轧制过程中轧辊的弹性变形和轧辊与轧件间的相互作用,通过对四辊轧机辊系变形和受力状况的分析,从理论上详细推导了直观的有载辊缝形状函数,明确了有载辊缝形状函数与相关因素的对应关系。
3)  Four High Mill
四辊轧机
1.
The axial overload is the main factor which causes work roll bearings and back up thrust bearings of four high mill invalid.
四辊轧机工作辊轴承及支承辊止推轴承失效的主要原因是轴向力过大。
4)  high mill
四辊轧机
1.
The finite element method is used to solve the deflection of rolls for 4-high mill.
采用有限元方法求解四辊轧机辊系变形问题,由于在工作辊及支承辊之间存在着未知接触压力和位移因而该问题无法用简单方法求解;根据辊系变形与受力的特殊性对方程进行变换可解出辊系各点位移,从而实现对辊系变形及辊缝形状进行较为准确的预报及控制。
5)  four-high mill
四辊轧机
1.
Influence of axial function at rolls in four-high mill upon the service life of roll bearing;
四辊轧机辊系间的轴向摩擦力对辊系轴承寿命的影响
2.
Free transverse vibration of rolls for four-high mill
四辊轧机辊系的横向自由振动
6)  4-high mill
四辊轧机
1.
For 2800mm 4-high mill, PMR (Plate Mill Backup Rolls with Variable Contact-Length), PWR (Plate Mill Work Rolls used for "deadflat" plate rolling) and a series of work roll contours configured for PMR are developed.
本文提出并建立了中厚板精轧机的工作辊与支持辊辊形解耦同步设计的理论和方法,依此创制出2800mm四辊轧机使用的变接触支持辊辊形(PMR)及配套的系列工作辊辊形和轧制超平材用的工作辊辊形(PWR),建立了相应的磨辊工艺制度。
2.
Introducing the simulation software based on influence function method for the elastic deformation of a 4-high mill system into computation of workpiece shape control process,the reason why the calculated average crown values of rolls are different from the relevant setup parameters are discussed and compared.
结合轧制过程中各道次轧制力、弯辊力及辊形曲线等实际数据,采用基于影响函数法的四辊轧机辊系弹性变形软件针对该典型产品的板形控制过程进行计算,分析了轧辊平均凸度计算值与设定值之间存在偏差的原因。
补充资料:宝山钢铁(集团)公司热轧带钢厂粗轧机组后的辊道保温


宝山钢铁(集团)公司热轧带钢厂粗轧机组后的辊道保温


宝山钢铁(集团)公司热轧带钢厂粗轧机组后的辊道保温
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条