1) corrosive wear resistant alloys
耐磨蚀合金
1.
Some designing principles concerning the composition and microstructure of corrosive wear resistant alloys have fully been discussed in present paper.
对耐磨蚀合金的成分与组织设计思想作了较全面的讨论。
2) Corrosion Resistant Alloy
耐蚀合金
1.
The stainless steels and high nickel corrosion resistant alloys are critical engineering materials.
不锈钢和高镍耐蚀合金是重要的耐蚀材料。
2.
Incoloy 825 is one of the most popular corrosion resistant alloys, and its corrosion resistance is closely related to the grain size.
Incoloy 825是目前最常用的耐蚀合金之一,其耐蚀性与晶粒的大小密切相关,细小而均匀的晶粒能极大地提高合金的耐蚀性,然而该合金在锻造成形中却存在如下的问题:变形抗力大,980℃时,其流动应力高达240MPa;加热和冷却时不发生相变,不能通过热处理方法细化晶粒,只能通过再结晶来细化晶粒。
3.
This paper introduces the current domestic and foreign research situation of the nickel-based micro corrosion resistant alloy(G-3) for oil country tubular goods(OCTG),and further studies the microstructural change of the alloy after aging treatments at 750℃.
介绍了油井管用镍基耐蚀合金G-3的国内外研究现状,并进一步研究了该合金在750℃长期时效后的组织变化。
3) corrosion resisting alloy
耐蚀合金
1.
The article introduces corrosion resisting alloys commonly used for petrochemical plants abroad, the common principle of material selection and the situation of material used for typical high temperature position in petrochemical equipments.
介绍了国外石化设备常用的一些耐蚀合金、选材的一般原则和石化装置典型高温部位用材情况。
5) wear resistant alloy
耐磨合金
1.
A wear resistant alloy consisting of Cr_(13) Ni_5Si_2 ternary silicide dendrites and the interdendritic nickel base solid solution (γ) was designed and fabricated by the laser melting/continuous deposition process.
采用激光熔化连续沉积工艺制备出了以CR_(13)Ni_5Si_2为初生相、以γ-Ni基固溶体为增韧相的金属硅化物耐磨合金,在室温干滑动磨损条件下测试了Cr1_3Ni_5Si_2／γ合金的耐磨性能并讨论了其磨损机理,结果表明,由于以Cr_(13)Ni_5Si_2／γ合金优良的强韧性配合以及在磨损过程中磨损表面上稳定氧化物转移覆盖层的快速形成,合金在室温干滑动磨损条件下具有优异的耐磨性能和很低的载荷敏感系数。
6) Wear Resisting Alloy
耐磨合金
1.
he wear position of new constructional guide plate is made from Ni-Cr wear resisting alloy.
新型结构导卫板磨损严重的部位用镍铬耐磨合金制造，其余部分用４５号涛钢，采用２次铸造方式使两者牢固地结合成一体。
补充资料：铂改性铝涂层IN738LC耐蚀高温合金热腐蚀产物
铂改性铝涂层IN738LC耐蚀高温合金热腐蚀产物
IIL_一_一了
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条