1) after-cure cooling
固化降温时间
2) Cooling time
降温时间
1.
Cooling time is an important parameter on MMR.
降温时间是ＭＭＲ制冷中的一个重要参数，加入高沸点组分，不仅可以维持较低的制冷温度并获得较大的制冷量，而且可以增大速冷性能。
2.
Through the analysis of the formula which was used to calculate the cooling time in mechanical ventilation,following two conditions were taken into account: the temperature of surface of grain stack was not decreased when the average temperature of grain stack reached goal temperature and the surface temperature was decreased during the aeration process.
通过对原有的机械通风降温时间的计算式进行分析,得出原有计算通风降温时间的方法未考虑到通风降温的两种情况:粮堆平均温度达终点温度时粮面温度未下降和通风过程中粮面温度已下降。
3) time temperature transformation cure diagram
时间-温度-转变固化图
1.
The time temperature transformation cure diagrams of the toughened and untoughened epoxy resins were obtained and compared between them.
用扭辫分析（ＴＢＡ）的方法研究了端羟基液体丁二烯－丙烯腈共聚物（丁腈羟，ＨＴＢＮ）增韧环氧树脂的固化行为，得到了增韧和未增韧环氧树脂的时间－温度－转变固化图（三Ｔ图，ＴＴＴ图）并进行了比较。
5) curing time
固化时间
1.
Effect of particle morphology of basic magnesium carbonate on viscosity and curing time of epoxy resin;
碱式碳酸镁颗粒形貌对环氧树脂黏度和固化时间的影响
2.
Effects of graphite content,curing time and curing temperature on the properties of the composite were studied with orthogonal test.
采用正交试验方法研究了石墨含量、固化时间以及固化温度对复合材料的影响。
3.
The curing time of the modified PF resin and the adhesive strength and emission of formaldehyde of the plywood bonded with this modified PF resin was measured in this paper.
研究了对紫胶改性酚醛树脂胶粘剂的固化时间、粘接胶合板的粘接强度和甲醛释放量进行了测定。
6) setting time
固化时间
1.
With the increasing of the MQ silicone resin,the crosslinkage of the silicone rubber was enhanced,setting time was prolonged and mechanical properties were improved.
以自制MQ硅树脂改善加成型室温硫化硅橡胶的性能,结果表明,MQ硅树脂可以增大加成型室温硫化硅橡胶的交联度,延长其固化时间,有效地改善其力学性能;含量为5%时,增强效果最好。
2.
Objective To develop and establish the testing methods appropriate for the determination of the working time and setting time of these materials using the Displacement rheometer.
目的利用移位式流变仪(Displacementrheometer),开发适当的测量组织调整材料的操作时间和固化时间的方法。
3.
The effects of seeding on the setting time, the compressive strength and the microstructure of the CPC were studied.
研究两种晶种对骨水泥固化时间、抗压强度和产物微观结构的影响。
补充资料：后固化时间
分子式：
CAS号：
性质：此为反应注射成型工艺中的一种参数，某些RIM工艺生产的产品，在脱模后需在一定温度下熟化一段时间，该段时间称之为后固化时间。目的是提高产品的机械性能。
CAS号：
性质：此为反应注射成型工艺中的一种参数，某些RIM工艺生产的产品，在脱模后需在一定温度下熟化一段时间，该段时间称之为后固化时间。目的是提高产品的机械性能。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条