1) scorch
[英][skɔ:tʃ] [美][skɔrtʃ]
焦烧
1.
The compounding agent A is used as modification agent to improve the scorching and solubility property of damping rubber.
采用复合助剂 A作改性剂来改善阻尼橡胶的焦烧性能和溶解性能。
2.
A few Kinds of anti-scorcher in NR blend cured with sulphur have a different mechanism of effect along with the change of accelerator type and blend of accelerators in curing System.
对胶料焦烧和硫化胶的性能以及热老化的影响也是不相同的。
3.
Surface scorch often occurs during the manuafcturing process for nylon sheathed wire.
在尼龙护套线的生产中护套表面焦烧现象时有发生,本文分析其产生的原因并采取相应的对策。
2) scorching
[英]['skɔ:tʃɪŋ] [美]['skɔrtʃɪŋ]
焦烧
3) Coke burning
烧焦
1.
For a long term, the coke burning time of the reforming catalyst in the semi-regeneration fixed bed reforming plant of Fujian Refining Chemical Co.
长期以来 ,福建炼油化工有限公司的半再生固定床重整装置由于重整催化剂烧焦时间与全厂大检修不能同步 ,而且催化剂处理时间长达 2 3d ,对全厂的罐容造成一定的压力 ,使汽柴油出厂受到影响。
2.
it expounds coke burning method ahead of styrene dehydrogenate catalyst unloading,including coke burning preparation,coke burning procedure and associated issues during the coke burning.
论述了卸出苯乙烯脱氢催化剂之前进行烧焦的方法,包括烧焦准备、烧焦程序以及烧焦过程中的有关事项。
3.
This paper introduces the reasons for poor coke burning effect in FCCUⅠ at SINOPEC Jiujiang Company,including low air flow rate for coke burning,poor stability of regenerator bed,low temperature zone resulted by catalyst returning from catalyst cooler,and low operating linear velocity in dense bed.
介绍了中国石化九江分公司Ⅰ套催化裂化装置烧焦效果较差的原因,包括实际烧焦风量不能满足烧焦需要、再生器床层稳定性差、外取热器催化剂返回造成低温区域的存在以及密相床层操作线速偏低。
5) coke preheating
焦粒焙烧
1.
A 1/4 full 3D computer model of 160 kA aluminum reduction cell during coke preheating was built by using finite element analysis software ANSYS.
以有限元分析软件ANSYS为平台,建立了160 kA铝电解槽焦粒焙烧时的三维1/4整槽模型;对3种典型阴极炭块(半石墨质、半石墨化和石墨化)在给定焙烧条件下的热场分布进行了仿真研究。
2.
The three-dimension transient thermal and structural ANSYS finite element model of quarter aluminum reduction cell was developed to predict the temperature profile due to coke preheating and evaluate the resulting thermal stresses in the cathode.
用大型商业有限元分析软件ANSYS建立三维瞬态1/4槽热和结构应力场模型,对铝电解槽焦粒焙烧过程中热应力场进行数值模拟,分析了焦粒焙烧所引起的阴极温度分布和热应力分布。
6) on-line decoking
在线烧焦
1.
The application of on-line decoking technology for the tubes in the 3-chamber furnace of a grass-roots 32 000 b/d delayed coker is introduced in respect of on-line decoking process flow, operation, operating precautions and decoking results etc.
介绍了加热炉炉管在线烧焦技术在扬子石油化工股份有限公司炼油厂新建1。
补充资料：焦烧
分子式：
CAS号：
性质： 胶料在加工过程或硫化前停放过程中出现早期硫化现象，又称自硫(bin cure)。导致胶料出现焦烧的原因主要是配方设计不当，如促进剂品种不合适、用量过大；混炼、压出、压延时温度过高；胶料停放温度过高、时间过长等。防止胶料焦烧除针对上述原因从配方、工艺上加以改进外，还可以通过使用防焦剂延长胶料的焦烧时间来达到。
CAS号：
性质： 胶料在加工过程或硫化前停放过程中出现早期硫化现象，又称自硫(bin cure)。导致胶料出现焦烧的原因主要是配方设计不当，如促进剂品种不合适、用量过大；混炼、压出、压延时温度过高；胶料停放温度过高、时间过长等。防止胶料焦烧除针对上述原因从配方、工艺上加以改进外，还可以通过使用防焦剂延长胶料的焦烧时间来达到。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条