1) ceramic mold
陶瓷模
1.
Ceramic mold used in HIP process was required to has not only proper strength at room temprature but also better plasticity at elevated temperature so the ceramic mold must be sintered in a special way.
热等静压用陶瓷模既要具有一定的室温强度，又要具有良好的高温塑性变形能力，因而需要采取特殊的烧结工艺。
2.
In this paper, the fabrication preocess of the ceramic mold, which includes the coating method, a new dewaxing technique and sintering process, was described.
粉末冶金陶瓷模工艺是一种适用于制备形状复杂零部件的接近成品形状的成形工艺技术。
2) ceramic die
陶瓷模具
1.
The ceramic die used to fabricate the denture base was made by mixing the green of ZrO_2 and TiO_2 with PVA and press them into oral cavity model to get the semi-finished ceramic die.
将ZrO2-TiO2陶瓷粉末与聚乙烯醇(PVA)溶液进行混合,压模成形后,在1300℃时无压烧结3h,制成与口腔形状吻合的、具有足够强度的超塑成形用陶瓷模具。
2.
The wear is taken as normal failure in the ceramic die of Cr12MoV steel.
Ｃｒ１２ＭｏＶ钢制陶瓷模具正常失效方式为磨损。
3.
This paper introduces the performance features and application fields of the polyurethane plastic cement,polyurethane building glass gasket cement,polyurethane waterproof coating materials,polyurethane heat-insulating materials,polyurethane wall/ground tiles and ceramic die,polyurethane heat-insulating and bridge-cut-off A-alloy door/window,polyurethane road joint strip,polyu.
分别介绍了聚氨酯塑胶、聚氨酯建筑玻璃密封胶、聚氨酯防水涂料、聚氨酯保温材料、聚氨酯墙地砖陶瓷模具、隔热断桥铝合金门窗、聚氨酯道路嵌缝胶、聚氨酯灌浆材料、艺术地坪模板的性能特点及其应用领域。
3) ceramic shell mould
陶瓷模壳
1.
The ceramic shell mould made of slurries of transition metal oxide sol and stabilized ZrO2 filler for the investment casting of titanium alloys was systematically investigated.
对适用于钛合金精密铸造用陶瓷模壳的制备工艺进行了系统的实验分析,表征了以过渡金属氧化物溶胶为粘结剂、稳定氧化锆为耐火材料的料浆的性能并讨论了相关参数的影响,对比研究了级配粉与均匀细粉制作的模壳的表面质量。
4) Rubber ceramic mold
橡胶陶瓷模
5) ceramic mould process
陶瓷模工艺
6) ceramic mould machine
陶瓷铸模机
1.
Failure analysis of a broken column of ceramic mould machine;
陶瓷铸模机立柱断裂原因分析
补充资料：陶瓷模印贴花
陶瓷模印贴花 见“陶瓷堆贴花”。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条