1) pressure actuated detonating
压力引爆
1.
A pressure actuated detonating system for underbalanced perforating that is compatible with packers is described in this article.
本文主要介绍了一种与封隔器相配的适用于多种井况的压力引爆负压射孔系统,尤其适用于大斜度井、水平井的再次负压射孔。
2) low-tension detonator
低压引爆器
3) explosion pressure
爆炸压力
1.
Removal of Overlarge Explosion Pressure for Large-Sized Flame-Proof Motor by New Material;
采用新材料解决大型隔爆型电动机爆炸压力过大的问题
2.
The results show that both the explosion pressure and the rising rate of explosion pressure increase with the decreasing of the size of aluminum particles.
利用自制的水平管道式气体-粉尘爆炸试验装置对不同粒度铝粉的爆炸压力进行测试。
3.
The present paper is aimed at reporting its research findings over the effect characteristic of the ignition energy on the brisance of the polynary mixed explosive gas and the effect of the energy on the explosion pressure of liquefied petro-gas through a gas explosion characteristic parameter testing system.
以密闭爆炸筒(20 L)内液化石油气(体积分数为5%)-空气混合气体为研究对象,逐步提高点火能量引爆混合气体,分析气体爆炸压力波形图的变化。
4) burst pressure
爆破压力
1.
Study of burst pressure calculation method of pipelines with axial flaws;
含轴向缺陷管道的爆破压力计算方法研究
2.
The burst pressure of filament wound pressure vessels and the ratio of strength transfer of fiber;
纤维缠绕压力容器的爆破压力与纤维强度转换率
3.
The prediction of the burst pressure of pressure vessels with miter pipe
轴向斜接管内压容器爆破压力的预测
5) Explosion Pressure
爆破压力
1.
On the basis of the test results of a full scale hot state explosion test a calculation and analysis was conducted of the explosion pressure of the following: square box test parts, nodular cast iron boiler, grey cast iron boiler and grey cast iron boiler plates.
基于一次大规模热态爆破试验的结果 ,分别对方箱试件、球墨铸铁锅炉的爆破压力、灰口铸铁锅炉和灰口铸铁锅片的爆破压力进行了计算和分析 ,得出安全系数选取的推荐值。
6) bursting pressure
爆破压力
1.
In this article, the influence of thickness reduction due to big deformation for bursting pressure of multilayered cylinder & spherical shells is analyzed.
用强度削弱系数分析了因大变形引起的壁厚减薄对多层容器爆破压力的影响 ,导出了多层圆筒形容器与球形容器爆破压力计算公式。
2.
By using mathematic model and Tresca yield criteria the total yield pressure and bursting pressure of flat ribbon-wound pressure vessel were discussed,the simple calculation formula for bursting pressure of flat ribbon-wound pressure vessel was given,the certification of practical example calculation was made for the accuracy and fineness of the calculated value.
通过数学模型,应用Tresca屈服准则,探讨了扁平绕带式压力容器的全屈服压力和爆破压力,给出了扁平绕带式压力容器爆破压力的简便计算公式,对计算值的准确度和精密度进行了实例计算验证。
3.
Based on that mechanism, the calculation formula for bursting pressure is derived.
通过实验得出正拱环向开缝型爆破片的破坏机理,由此导出正拱环向开缝型爆破片的爆破压力计算公式。
补充资料：锅炉、压力容器、压力管道及特种设备定期检验
锅炉、压力容器、压力管道及特种设备定期检验
periodic inspection of boilers, pressure vessels, pressure piping and special equipment
guolu YOli侧飞扣1 YOli gLJal对印ji tez陌叩劝以拍1 dingqi】，on四n锅炉、压力容器、压力管道及特种设备定期检验(peri诫c inspectionof城le。，p~切reves-Sels，p~二piPing ands衅过闪uiplr屺nt)为保证设备的安全使用，规定设备必须按一定周期进行法定的、强制性的检验。定期检验由政府设立的检验所、使用单位或行业检验站进行。检验单位及检验人员必须具有与所检设备相适应的资格。设备使用单位应该建立定期检验制度，做好检验计划，按时向检验单位提出申请。检验单位应该保证及时进行检验，检验按有关检验规则进行。检验时，设备使用单位应做好配合工作，提供必要的运行资料。检验完毕，检验单位要出具检验报告，对设备能否使用，要作出明确结论。如设备有缺陷，要提出是否修理、监护使用和报废的处理意见。锅炉压力容器安全监察机构根据检验机构的报告，发使用许可证书。有缺陷的，责令使用单位修理，修理后检验仍不符合安全要求的，则通知报废。使用单位逾期不进行定期检验，锅炉压力容器安全监察机构有权停止其设备运行。(陈亦惠)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条