1) residual air hole
残余孔洞
3) Residual Pores
残余气孔
4) shrinking hole remnant
缩孔残余
1.
After making fracture analysis, chemical analysis and metallographic examination to the broken ped estal, It is concluded that the main reason are the harden layer,original crack and shrinking hole remnant flaw existing on the raw material.
对断裂后的支撑座进行了断口、化学成分、金相组织分析,认为原材料存在淬硬层、原始裂纹及缩孔残余缺陷是导致断裂的主要原因。
5) residual porosity
残余气孔率
1.
SiC/Al composites were fabricated by pressureless infiltration technique, based on infiltration dynamics mechanism and technic method ,the effects of holding time and cooling way on the residual porosity of composites were discussed.
采用无压浸渗法制备了SiC/Al复合材料,从浸渗动力学和工艺方法的角度探讨了浸渗保温时间和降温方式对复合材料的残余气孔率的影响。
2.
Through analyzing the fracture microstructure, measuring line-shrinkage rate, density and residual porosity of sintered sample, the influence of sintering temperature on density and the influence of the type of dispersant on residual porosity of sintered sample were studied.
通过对烧结体断面显微结构的分析,以及对烧结体的线收缩率、密度和残余气孔率的测定,研究了烧结温度对坯体烧结致密化性能的影响和分散剂种类对烧结体残余气孔率的影响。
6) residual intergranular pore
残余粒间孔
1.
It is concluded that these clastic reservoirs have low compositional and textural maturity, diagenesis is the early deep-burial later elevating type, pore types are constituted of residual intergranular pores, small amount of dissolution intergranular pores, ma.
在微观研究的基础上,对储集层沉积埋藏史、岩石学特征、孔隙结构、成岩作用以及孔隙演化特征等进行系统分析,认为哈密坳陷三叠系至下侏罗统碎屑岩储集层成分和结构成熟度低,成岩作用属早期深埋晚期抬升型,孔隙类型组合是以残余粒间孔-少量溶蚀粒间孔-大量微孔隙-成岩缝为主的组合,孔隙结构差,成岩阶段大部分已进入晚成岩B亚期。
补充资料：C10-12-烷基苯衍生物蒸馏残余
CAS：68988-79-4
分子式：Whole alkyl C10-12-benzene bottoms
中文名称：C10-12-烷基苯衍生物蒸馏残余
英文名称：Benzene, C10-12-alkyl derivs., distn. residues； C10-12-Alkylbenzene bottoms； Benzene,C10-12-alkyl derivs.,distn. residues
分子式：Whole alkyl C10-12-benzene bottoms
中文名称：C10-12-烷基苯衍生物蒸馏残余
英文名称：Benzene, C10-12-alkyl derivs., distn. residues； C10-12-Alkylbenzene bottoms； Benzene,C10-12-alkyl derivs.,distn. residues
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条