1) pre-heating temperature
预加热温度
2) preheating temperature
预热温度
1.
Effect of gasifying agent preheating temperature on pressurized turbulent CFB coal gasification
气化剂预热温度对加压湍动循环流化床煤气化的影响
2.
The influence of preheating temperature on the quality of BGA solder ball
预热温度对BGA钎焊球质量影响
3.
The microstructure of the liquid forging pieces under various specific pressures and preheating temperature conditions for the die were comparatively analyzed.
叙述了选用ZA27合金采用液态模锻工艺生产耐磨衬板的研究,确定了模具材料的选择及其热处理工艺,对不同比压及不同模具预热温度条件下液锻件的微观组织进行了对比分析。
3) preheat temperature
预热温度
1.
In this paper, the necessary preheat temperature was calculated by using “WELD CALCULATION” software, and the calculated results were verified by Implant and Tekken test.
采用“WELDCALCULATION”专用软件对Q390E、Q4 2 0E两种钢材的最低预热温度进行了计算 ,并采用插销试验和小铁研试验对计算结果进行了验证 ,在此基础上确定了松花江斜拉大桥钢梁不同厚度Q390E、Q4 2 0E钢板的焊接预热温度 ,研究成果在桥梁的焊接生产中得到成功应
2.
This paper analysed the cause of the heat energy consumption high, some improving preheat temperature and decreasing digester heat resources's way have been put forward.
本文通过对高压溶出热能消耗高的原因分析,提出了提高预热温度是降低高压溶出热能消耗的有效途径,可达到增产节能的目的。
3.
The effect of W content and preheat temperature on phase components and powder size of combustion synthesized product in Ti W C system were studied.
研究了 W含量及预热温度对 Ti- W- C体系燃烧合成产物相组成及粉末形貌的影响。
4) Heating Temperature
加热温度
1.
Experimental research on heating temperature of hot-reclamation of used resinbonded sands;
树脂旧砂热法再生加热温度的研究
2.
Effect of the heating temperature and heat retaining time on the inner crack healing in steel;
加热温度及保温时间对结构钢内部裂纹愈合的影响
3.
With the increasing of heating temperature,TiO2 film formed on pure titanium surface;the oxidation weight gain increased.
结果表明,在300~1100℃,随着加热温度的升高,纯钛氧化加重,形成氧化钛膜;300~500℃,纯钛试样增重0。
5) preheat plateau
预热温度坪
1.
Equivalent dose(De)preheat plateau test is an often used approach to determine an appropriate preheat temperature in optically stimulated luminescence(OSL)dating.
等效剂量预热温度坪实验是光释光(OSL)测年中确定预热温度的常用手段,一般选择坪区温度作为OSL测年的预热温度。
6) heating and temperaturel
加热和温度
补充资料：设备安装前的准备工作——设备的预装配与预调整
设备安装前的准备工作——设备的预装配与预调整 | ||
|
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条