1) sulfonitriding
硫氮共渗
1.
A new method of sulfonitriding processing by induction heating has been developed This technique can save energy and elimate environmental pollution and mak the workpiece obtaining good properties,such as wear resistance,corrosion resistance,thermal fatigue resistanc
利用高频热源开发硫氮共渗新技术，可节约能源，减少环境污染，并使零件获得耐磨、耐蚀、耐热疲劳等综合性能。
2.
The high freguency sulfonitriding layers has been characterized by using X-ray diffraction method in this paper.
本文利用X射线衍射仪对高频硫氮共渗层的相结构进行了分析,发现渗层表层部位主要由FeS、Fe_3O_4及ζ-Fe_2N等相组成,中间白亮层为ζFe_2N+ε-Fe_3N,扩散层由α-Fe+ε-Fe_(2-3)N等组成。
3.
This paper deals with the wear resistance and anti-seizing behavior of sulfonitrided high speed steel by comparing with that without sulfonitriding.
研究了高速钢经硫氮共渗处理后的耐磨性及抗咬合性，并与未经表面处理的试样进行了比较。
2) sulpho carbonitriding
硫碳氮共渗
3) sulphonitrocarburizing
硫氮碳共渗
4) liquid sulpho-nitrocarburizing
液体碳氮硫共渗
1.
The microstructure morphology of 38CrMoAl steel axial plunger after gas nitrocarburizing and liquid sulpho-nitrocarburizing were analyzed and observed by optical microscope and SEM,and the chemical composition of the penetrated layer were measured qualitatively by energy spectrum analysis.
用金相显微镜和扫描电镜观察和分析了38CrMoAl钢轴向柱塞经气体氮碳共渗和液体碳氮硫共渗后的组织形貌,并且用能谱分析的方法定性地测定了渗层的化学成分。
5) ion S-N-C co-diffusion
离硫氮碳共渗
6) sulpho-nitrocarburizing in salt bath
液体硫氮碳共渗
补充资料：碳氮硫三元共渗
分子式：
CAS号：
性质：又称硫氰共渗。可同时改善钢及铸铁工件的耐磨性及减磨性。共渗层深度为10μm，其组织与渗剂的组成有关。以渗硫为主时，表层有FeS或FeS加α-Fe；以渗氮为主时，有Fe2(N，C)及Fe4(N，C)；以渗碳为主时，则形成Fe3(C，N)。其工艺主要有粉末法、膏剂法和盐浴法三种。
CAS号：
性质：又称硫氰共渗。可同时改善钢及铸铁工件的耐磨性及减磨性。共渗层深度为10μm，其组织与渗剂的组成有关。以渗硫为主时，表层有FeS或FeS加α-Fe；以渗氮为主时，有Fe2(N，C)及Fe4(N，C)；以渗碳为主时，则形成Fe3(C，N)。其工艺主要有粉末法、膏剂法和盐浴法三种。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条