1) Eccentric block
偏心块
1.
The paper introduces three methods of calculation of eccentricity for vibratory roller s semicircleeccentric block, compares the three results of calculation with example.
介绍了振动压路机半圆形偏心块偏心矩的3种计算方法,并利用设计实例对这3种方法的计算结果进行了比较,计算误差在1%以内,并推荐使用三维软件的设计方法。
2.
According to the requirements of overall characteristics of roll leveling machine on dynamic properties of vibrating roller and through man machine interaction, the dynamic design of eccentric block in vibrating roller has been made and a more ideal structure has been found out, providing a theoretical basis for primary design of structure.
根据滚平机整机性能对振动辊动力特性的要求 ,通过人机交互方式 ,对振动辊中的激振偏心块进行了动态设计 ,找出了较理想的结构方案 ,为结构初期设计提供了理论依据。
2) wobbler shaft
偏心块轴
1.
The vibration, which is obtained through shock excitation electric engines driving tow symmetric wobbler shafts, makes the com.
其振动成型原理是通过激振电机驱动对称安装在振动台上的偏心块轴，产生激振力使振动台产生所需的振动，由于振动使被压实材料内产生振动冲击。
3) eccentric shoe
偏心滑块
4) eccentric slide block balancing mechanism
偏心滑块平衡机构
1.
The kinematical and dynamic behaviors of an eccentric slide block balancing mechanism are analyzed here.
文章运用运动学和动力学知识对一种新型的单缸发动机平衡机构——偏心滑块平衡机构进行理论分析,推导出不平衡惯性力和惯性力矩与设计参数间的关系,并提出了偏心滑块平衡机构的设计准则,研究成果应用于某园林发动机上,实验验证了理论分析和设计的正确性。
5) Off-center
[英]['ɔ:f'sentə] [美]['ɔf'sɛntɚ]
偏心
1.
Two methods about how to calculate the bearing off-center of curved beam bridge are presented,which is common but no conclusion now.
根据恒载条件下横桥向双支座反力相等原则,对曲线梁桥设计中常见但尚无定论的支座偏心问题提出了2种计算方法,即最小偏心法和一致偏心法。
6) eccentric
[英][ɪk'sentrɪk] [美][ɪk'sɛntrɪk]
偏心
1.
Topography guided LASIK on correction of eccentric ablation;
角膜地形图引导准分子激光一次性矫治角膜切削偏心
2.
A Convenient Design Method for Eccentric Bridge Pier and Abutment;
一种简便的偏心墩台设计方法
3.
The real time detector method of multi-cable eccentric degree;
多线芯电缆偏心度的在线检测
补充资料：在AutoCAD中偏心圆锥与偏心圆台实体的画法
现在要画一个偏心圆锥,底面在WCS的XY平面上,圆心(0,0,0),半径100,顶点(300,0,400)在ZX平面上.
1)连接PA,PB. A(-100,0,0) B(100,0,0)
图1
在当前坐标下:
2)延长PA到C,使PA=CA;延长PB到D,使PB=DB;
3)连接CD;
4)以CD为直径画圆;
5)用XLINE命令中的二等分选项作角CPD的角平分线PO,交CD于O;
6)过O作CD的垂线,交圆于E,F;
图2
7)用三点UCS命令,取三点为:O,P,C;
8)过点O作PO的垂线GO,交PC于G;
图3
9)再次用三点UCS命令,取三点为O,F,G;
10)现在就可以画椭圆锥了!
cone-e-c-捕捉O点-捕捉F点-捕捉G点-a-捕捉P点;
图4
11)回到WCS,剖切椭圆锥
SL-选择椭圆锥-回车-XY-回车-捕捉P点.
12)删除辅助线条.
图5
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条