1) oxygen transfer
充氧特性
1.
Hydrodynamics and oxygen transfer of typical internal loop biological fluidized bed were studied according to different holdup of AC carriers with biofilm.
以挂膜后的活性碳为载体,在不同投加率下研究了典型内循环生物流化床的水力特性及充氧特性。
2) oxygenation capacity
充氧性能
1.
Time control in testing of clean water oxygenation capacity of aerators;
曝气设备清水充氧性能测试时间的控制
2.
Comparing with other media, when the volume ratio of extender to reactor of the new Nanometer suspended extender was 30%, the oxygenation capacity could reach 0.
比较了国内几种常见的填料,新型纳米悬浮填料在30%的投配率下OC值(充氧性能)就达到了0 071kg/h。
3.
Two stage up-flow biological aerated filters with modified polystyrene have been used in experiment, and oxygenation capacity, biofilm attachment and the effect of sanitary waste treatment are analyzed.
本试验将经过改性的聚苯乙烯轻质填料应用于上流式两级曝气生物滤池中,并对其充氧性能,挂膜启动以及处理生活污水的效果进行了分析。
3) Filling Behavior
充型特性
1.
Numerical Simulation of Filling Behavior in Lost Foam Casting;
基于计算机模拟的消失模铸造充型特性
4) filling peculiarity
充填特性
1.
It has filling peculiarity of highwater rapidsolidifying material, mass rock cementing fill and commonly tailings cementing fill, and its filling body takes a good refrain impact on the implacement of stope and shaft wall and those stress varying.
在山东某金矿竖井保安矿柱回收试验研究中,采用了高水速凝废石浇注充填的新工艺,它具有聚高水速凝材料、块石胶结充填、普通尾胶充填的充填特性,其充填体对采场及井筒帮壁的位移和应力变化起到了良好的抑制作用。
5) charging character
充电特性
1.
This paper introduces the charging character of Ni/Cd and Ni/MH battery,and proposes a fuzzy control system for intelligent fast charging.
为了实现充电过程的智能控制,在研究镍镉、镍氢电池充电特性的基础上,用模糊控制技术对充电过程进行智能控制。
6) charging characteristics
充液特性
1.
A mathematical model of charging characteristics in a full power hydraulic brake system was established based on the structure and performance analysis of a new-type accumulator charging valve.
在对新型蓄能器充液阀结构与性能分析的基础上,建立了制动系统充液特性动态分析数学模型,分析了充液过程中充液阀的动态特性及功率消耗,得到了系统参数及充液阀结构参数对充液特性的影响规律。
2.
A mathematical model of constant pressure and flow rate charging characteristics in a full power hydraulic brake system was established based on the structure and performance analysis of a new-type accumulator charging valve.
在对新型蓄能器充液阀结构与性能分析的基础上,建立了全液压制动系统恒压及恒流充液过程数学模型,得到了影响充液速度及时间的系统参数及蓄能器与充液阀的结构参数,利用Simulink进行仿真,分析了节流口浮动时系统参数及充液阀结构参数对充液特性的影响规律,实验验证了仿真模型的正确性。
补充资料：充炭黑充油丁苯橡胶
分子式：
分子量：
CAS号：
性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
分子量：
CAS号：
性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条