1) cold rolled shape
冷轧板形
1.
Research into the intelligence control of cold rolled shape based on fuzzy neural network;
基于模糊神经网络进行冷轧板形智能控制的研究
2) cold-rolled steel sheet
冷轧钢板
1.
The corrosion resistance of cold-rolled steel sheet was studied by electrochemical tests including linear polarization(LP)and electrochemical impedance spectroscopy(EIS).
采用线性极化、电化学交流阻抗等方法研究了冷轧钢板的耐蚀性能,同时使用线性扫描伏安法获得了冷轧钢板表面氧化物的种类及还原电位,分析了其与冷轧钢板耐蚀性能之间的关系。
3) cold-rolled sheet
冷轧薄板
1.
Experimental study of recrystallization of cold-rolled sheets produced by CSP hot bands;
CSP冷轧薄板再结晶试验研究
2.
The main production process,equipments collocation and advanced technologies of the primary cold-rolled sheet project are introduced in this paper.
介绍了莱钢冷轧薄板(一期)工程的主要生产工艺、设备配置及先进技术。
3.
Newly-built cold-rolled sheet project in Jigang is introduced and the process flows, technological characteristics and the technical parameters of main facilities in 110×104 tons continuous pickling line, 84×104 tons cold rolling line, 43×104 tons annealing line, 48×104 tons leveling line and 33×104 tons recoiling and cutting line are analyzed with emphasis.
介绍了济钢新建冷轧薄板项目的情况,重点介绍了110万t连续酸洗线、84万t冷轧线、43万t退火线、48万t平整线和33万t重卷分卷线的工艺流程、技术特点及主要设备技术参数。
4) cold rolled sheet
冷轧板
1.
Progress of research on inclusion induced surface defect of cold rolled sheet
冷轧板夹杂类表面缺陷研究的进展
2.
The microstructure of continuous casted plate ,cold rolled sheet and annealed sheet of 3003 aluminium alloy were observed by photo-electro metallographical machine, the mechanical properties were obtained through mechanical property test.
利用光学显微镜观察3003铝合金铸轧板、冷轧板以及冷轧板退火后的显微组织,用电子拉伸试验机进行拉伸试验,获得不同退火温度下铝板的力学性能,讨论了退火温度对该合金显微组织、抗拉强度和伸长率的影响。
3.
The macroexamination and micro-examination of the characteristics of the common cavity defect in cold rolled sheet of low carbon Al-killed steel were carried out.
对生产中常见的低碳铝镇静钢冷轧板孔洞缺陷特征进行了宏观和微观分析。
5) cold rolled sheet
冷轧钢板
1.
Technology and installations for the production of cold rolled sheet at PZH Steel were introduced.
简要介绍了攀钢冷轧钢板生产的技术、装备情况 ,分析了攀钢冷轧钢板在家电产品中的应用现状及发展前景。
6) cold-rolled strip
冷轧薄板
1.
A cold-rolled strip plate-profile recognition method was presented to improve the detection accuracy based on image morphology processing method.
为了解决冷轧薄板板形识别问题,采用基于形态学的图像处理方法。
2.
A cold-rolled strip plate-profile recognition method was presented to improve the detection accuracy based on image processing.
为了解决冷轧薄板板形识别问题,采用基于图像处理的方法,对图像进行直方图均衡化,使处理后的图像对比度、图像边界的清晰度有了很大的提高,并在此基础上再进行形态学增强,改善图像效果。
补充资料：宝山钢铁(集团)公司冷轧带钢厂板形仪原理图
宝山钢铁(集团)公司冷轧带钢厂板形仪原理图
宝山钢铁(集团)公司冷轧带钢厂板形仪原理图
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条