1) heat temperature resisting sliding lumps
耐热滑块
1.
The can weldability contrast test of heat temperature resisting sliding lumps in heating furnacesvertical waterpipe is introduced,a effective welding method is summarized.
介绍了加热炉纵水管耐热滑块的可焊性对比试验 ,总结了一套行之有效的焊接方法 ,对确保焊接质量有一定参考价值。
2) heat resistant
耐热
1.
Synthesis of novel high heat resistant epoxy resin containing naphthyl structure;
一种新型含萘环结构高耐热型环氧树脂的合成
2.
Study on heat resistant epoxy resin adhesive with high peel strength cured at room temperature;
室温固化高剥离耐热环氧树脂胶粘剂
3.
Development of Casting Dual-Phase Heat Resistant Alloy Fe-Cr-Ni-Al;
铸造Fe-Cr-Ni-Al双相耐热合金的研制
3) heat-resistance
耐热
1.
The tray is a typical frame-shaped casting,it should have the abilities of heat-resistance,heat impact-resistance and crack-resistance through using different technologies and improving the technologies,make a simulated analyze on pouring system through CAST soft,investment casting CAE software.
薄壁耐热钢托盘属于典型的筐架结构型铸件,要求其有较高的耐热性、耐热冲击及抗裂能力。
2.
The mechanism of wear-resistance,heat-resistance and corrosionresistance of high chloride cast iron are analyzed respectively.
分析了高铬铸铁具有的抗磨、耐热、耐蚀性机理。
3.
A new duple-phase heat-resistance steel used at above 1 000 ℃ was obtained by adding some Ni to an original ferrite heat-resistance steel.
在高铬铁素体单相耐热钢的基础上,加入一定量的镍,得到一种新的奥氏体-铁素体双相耐热钢,并对该铬镍双相耐热钢的组织特征及常温和高温性能进行了测定。
4) heat-resistant
耐热
1.
Study on preparation and properties of heat-resistant epoxy adhesive cured at room temperature;
室温固化耐热环氧胶粘剂的制备与性能研究
2.
Fire test on a non-heat-resistant fireproof glass with down-flowing water film;
带雨淋水膜的非耐热防火玻璃的火灾试验(英文)
3.
Research present state and development of heat-resistant epoxy adhesive cured at room temperature;
室温固化耐热环氧胶粘剂的研究现状及进展
5) heat resistance
耐热
1.
Influence of three kinds of surface dispersants on the activity and heat resistance of Ru/AC catalyst for ammonia synthesis;
3种表面分散剂对Ru/AC氨合成催化剂的活性和耐热性的影响
2.
Effect of several kinds of antioxidant on heat resistance properties of chlorinated polyethylene;
防老剂对氯化聚乙烯耐热性能的影响
3.
Casting Magnesium Alloy of Mg-Nd-Zn-Zr Series with Heat Resistance and High Strength;
Mg-Nd-Zn-Zr耐热高强铸造镁合金
6) heat tolerance
耐热
1.
Studies on methodlogy for identification of heat tolerance of tomato;
番茄耐热性鉴定方法研究
2.
Studies on Physiological and Molecular Genetics Basis of Heat Tolerance of Two Early Rice Cultivars;
两个早稻品种耐热性生理及分子遗传基础的研究
3.
As one of the environment stress factors, high temperature is often suffered in the protected field at summer, and the heat injure of cucumber, a major vegetable cultivated in protected condition, has become one of the main factors disturbing its normal growth, so how to improve the heat tolerance of cucumber has been one of the important research target in cucumber breeding.
如何提高黄瓜耐热性是目前黄瓜育种研究的重要内容之一。
参考词条
补充资料：EMX初级+滑块教程
1.利用 EMX 4.0->项目->新建 创建新的EMX组合
注意事项!
如果要自动保存文件
请进行如下设置
EMX 4.0->帮助->选项->配置选项
加入设计好模具组合文件!
2.利用 元件->装配 将设计好的模具组合文件装配进来
利用缺省或利用对齐坐标系的方法
建议使用对齐坐标系的方法
示例
1.使用缺省坐标进行装配
注意:你的模具组合文件的缺省坐标系X.Y平面必需在分模面上
2.如果不是请另在分模处建立坐标系利用对齐坐标系的方式进行装配!
3.对组模具组件进行分类
EMX4.0->项目->准备
注意:这一步的分类非常重要EMX可以根据你分类将零件放到相应的层及简化表示上!及开模动画中!
4.调入模架及其它元件
EMX 4.0->模具基体->组件定义->载入或保存组件(选择你需要的模架)->载入->确定
注意事项!如果要自动保存文件
请进行如下设置
EMX 4.0->帮助->选项->配置选项
加入设计好模具组合文件!2.利用 元件->装配 将设计好的模具组合文件装配进来
利用缺省或利用对齐坐标系的方法
建议使用对齐坐标系的方法
示例1.使用缺省坐标进行装配
注意:你的模具组合文件的缺省坐标系X.Y平面必需在分模面上
2.如果不是请另在分模处建立坐标系利用对齐坐标系的方式进行装配!
3.对组模具组件进行分类
EMX4.0->项目->准备
注意:这一步的分类非常重要EMX可以根据你分类将零件放到相应的层及简化表示上!及开模动画中!
4.调入模架及其它元件
EMX 4.0->模具基体->组件定义->载入或保存组件(选择你需要的模架)->载入->确定
说明：补充资料仅用于学习参考，请勿用于其它任何用途。