1) Impact energy
冲击能
1.
At first the γ-austenite to ε-martensite phase transformation absorbed a great deal of impact energy.
空泡冲击能诱发奥氏体到马氏体的相变,并被其吸收;当相变达到饱和点时,马氏体片层开始吸收冲击能,同时逐渐发生扭曲和断裂,最终马氏体片层断裂产生的碎片大量剥落,该材料的空泡腐蚀潜伏期结束。
2.
Because of clearance leakage,the effect coefficients of piston impact velocity,impact energy,average input pressure and work efficiency are found.
通过对液压锤内间隙泄漏问题的研究,找出了间隙泄漏量对活塞的冲击末速度、冲击能、冲击频率以及液压锤的平均输入压力和工作效率的影响系数,在考虑所受间隙泄漏、粘性摩擦力、密封阻力的因素影响下建立液压锤的数学模型,和未考虑影响因素情况下建立的简化数学模型,分别进行仿真研究,得到了2种情况下仿真模型的影响系数,并将得出的数据进行了分析,对改进和优化液压锤的设计参数具有指导意义。
3.
WT5BZ]In this paper, these parameter, impact energy, yield stress, maximum stress, and strain have been obtained using impacting energy testing for SiCp reinforced aluminum matrix composites with low ductility.
用冲击能量法 ,对低延性 Si C颗粒增强铝基复合材料得到冲击能外还得到动态屈服载荷、最大载荷、失稳载荷以及应变等多种参量 ,综合分析了温度对各种参量的影响 ,提出了总能量与温度关系曲线上的第一峰可作为低延性材料的最佳使用温
2) impact properties
冲击性能
1.
Analysis of relationship between interstitial content and impact properties of a type of near α titanium alloy;
一种近α钛合金间隙元素含量和冲击性能关系分析
2.
Effect of fillers on impact properties of high molecular weight polyethylene;
填料对超高分子量聚乙烯冲击性能的影响
3.
Effect of δ-ferrite on impact properties of 12%Cr rotor steel for ultra-supercritical steam conditions;
δ铁素体对12%Cr超超临界转子钢冲击性能的影响
3) impact energy
冲击能量
1.
The dynamic impact response behaviors of TiNi alloy at various impact energy and temperature were studied using the simple pendulum impact testing system.
利用单摆冲击试验设备,对TiNi合金不同冲击能量及温度条件下的冲击响应行为进行了研究。
2.
The article describes determination of the characteristic values of impact energy and its use such as steel ductile-brittle transition.
介绍了冲击能量特征值的测定及其在钢的冷脆转变等方面的应用。
3.
the results showed that the life of initial peeling off depending on impact energy and impact frequency,and it is also related to surface roughness.
结果表明，端面起始剥落寿命主要取决于冲击能量和冲击频率，也和端面粗糙度有关。
4) impact toughness
冲击性能
1.
Influence of gas content on impact toughness of deposited metal of martensitic stainless steel;
气体含量对马氏体不锈钢熔敷金属冲击性能的影响
2.
The method of improving the impact toughness of non quenching and tempering steel by controlling the content of minor elements and the hot working technology is discussed.
通过在 40 Mn V钢中控制微量元素含量并控制热加工工艺 ,探讨提高非调质钢冲击性能的方法。
3.
The influences of B content and Nb,V micro-alloying on the impact toughness of low carbon boron steel were investigated by impact tests of low carbon boron steels with different boron contents and of Nb,V micro-alloyed low carbon boron steel.
通过对不同B含量的低碳硼钢和Nb、V微合金化低碳硼钢的冲击实验,研究了B含量及Nb、V微合金化对低碳硼钢冲击性能的影响。
5) impact performance
冲击性能
1.
Effect of nitrogen on the impact performance of low alloyed structure steels;
低合金结构钢中氮对冲击性能的影响
2.
Has proven between the plastic differentmolding impact performance and the size rate of change and otherperformance as well as two targets relevance with emphasis withenhances some performance the prerequisite, enhances each performancefor the synthesis, proposed the corresponding adjustment measure.
本文重点论证了塑料异型材冲击性能与尺寸变化率和其他性能,以及两项指标之间的相关性与提高某项性能的前提条件,为综合提高各项性能,提出了对应调整措施。
3.
This paper,for the first,has used pendulum impact method and even elastic support falling weight bend impact method to give comparison test to impact performance of flexible fiber cement stabilize gravel and common cement stabilize gravel.
运用摆锤冲击法和均匀弹性支撑落重弯折冲击法,首次对柔性纤维水泥稳定砂砾和普通水泥稳定砂砾的冲击性能进行了对比试验研究。
6) impact strength
冲击性能
1.
Different types of EP/PU graded IPNs were prepared by means of casting layer by layer,and its impact strength was studied.
研究了采用梯度IPNs方法提高环氧树脂的冲击性能,设计了新型梯度组分分布数学模型描述梯度组分的分布,采用梯度因子和梯度层数控制梯度IPNs的结构变化。
2.
The impact strength of glass mat reinforced EVA/PP is discussed in this paper.
研究了EVA改性PP/GMT复合材料的冲击性能,结果表明:EVA改性PP可有效的提高复合材料的冲击性能。
3.
However, when the density is fixed, the impact strength is decreased with the adding of SiO 2 particles.
本文研究了SiO2 和纤维增强剂对于聚氨酯硬泡塑料冲击性能的增强效应。
补充资料：标准操作冲击电压波形(见冲击电压发生器)
标准操作冲击电压波形(见冲击电压发生器)
standard switching impulse voltage waveform
b .oozhun CooZuo ChongJld，onyo boxlng标准操作冲击电压波形(standard switchingimpulse voltage waveform)见冲击电压发生器。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条