1) sewage dewatering sludge
污水脱水污泥
1.
Municipal solid waste (MSW), sewage dewatering sludge (SDS) and drain sludge (DS) are the main pollutant problem in modern cities.
城市垃圾和污水脱水污泥、排水管污泥已成为现代城市污染的主要问题。
2) sludge dewatering
污泥脱水
1.
Synthesis of cationic and weight molecular flocculant used in sludge dewatering;
高分子量阳离子型污泥脱水剂的合成
2.
Dosage of chitosan flocculant influencing on sludge dewatering performance;
壳聚糖絮凝剂的投加量对污泥脱水性能的影响
3.
Experimental study on optimum dosage ratio for sludge dewatering in Yangjiapu sewage plant;
杨家堡污水厂污泥脱水最佳投药比试验研究
3) dewatered sludge
脱水污泥
1.
The effects of various dewatered sludge loadings(0,165,330,495 and 660(t/hm~2) respectively) in soil on growth of Canna were studied.
在脱水污泥施用量分别为0,165,330,495和660 t/hm2时对美人蕉生长情况的影响进行了研究,同时研究了污泥的施用和美人蕉的种植对土壤中重金属含量的影响。
2.
Bioflocculant JT06 was extracted from dewatered sludge by ultrasonication,acetone precipitation and freezing desiccation.
以城市污水处理厂的脱水污泥为原料,通过超声波破碎、丙酮沉淀及冷冻干燥得到了微生物絮凝剂JT06,同时对该絮凝剂的制备条件及絮凝特性进行了研究。
3.
The dewatered sludge was added with various additives to be landfilled,and the variation of heavy metal speciation in sludge during initial and final landfill stages was investigated.
采用不同添加剂与污水处理厂的脱水污泥进行混合填埋,考察了填埋初期和后期污泥中重金属形态的变化。
4) sludge dehydration
污泥脱水
1.
Preparation and application of a novel environmental flocculant to sludge dehydration;
一种新型环保型污泥脱水絮凝剂的研制与应用
5) drainable sludge
易脱水污泥;可脱水污泥
6) sludge liquor
污泥脱水液
1.
Coupling process of partial nitrification and ANAMMOX for treatment of sludge liquor
部分亚硝化-厌氧氨氧化耦合工艺处理污泥脱水液
2.
It is undesirable to discharge sludge liquor from the wastewater treatment plant to the surface water,because it is rich in phosphate(PO~(3-)_4)and ammonium(NH~+_4),and these nutrients can accelerate eutrophication in the surface water.
研究污水处理厂产生的污泥脱水液中的磷酸盐(PO43-)和铵盐(NH4+)的去除方法。
3.
The sludge liquor was studied in this paper.
污泥脱水液属于低碱度、低C/N、高氨氮废水,采用传统的生物硝化/反硝化工艺已不能满足这类低C/N、高氨氮废水的处理要求。
补充资料：脱水污泥
分子式：
CAS号：
性质：利用排水或过滤的方法使湿污泥脱水后剩余的固体残渣。脱水的污泥一般比浓缩的或液态的污泥容易贮运。通常，污泥在焚化前要求脱水，以去除污泥水分，增加热值。污泥在填埋前一般也要求先脱水，以减少填埋场的沥滤液产生量。
CAS号：
性质：利用排水或过滤的方法使湿污泥脱水后剩余的固体残渣。脱水的污泥一般比浓缩的或液态的污泥容易贮运。通常，污泥在焚化前要求脱水，以去除污泥水分，增加热值。污泥在填埋前一般也要求先脱水，以减少填埋场的沥滤液产生量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条