|
|
1) Dameigou section
大煤沟剖面
1.
It has been found out that the mother rocks of erosion provenance are mainly mid-low - grade metamorphic rocks, sedimentary rocks, as well as acidic and basic rocks by the heavy mineral analysis of Dameigou section in northern Caidam basin.
提出了重矿物特征指数ＡＴｉ和ＧＺｉ的韵律性和相关性的存在，并依此把大煤沟剖面中生代地层划分为５个重矿物韵律层，分析了它们在揭示源区岩性变化及在地层划分与对比中的作用。
2) Yangou section
沿沟剖面
1.
The Conodont Fauna of late Permian to early Triassic from Yangou section in Leping area,Jiangxi Province was discussed in this paper.
讨论了赣中乐平地区沿沟剖面上二叠统至下三叠统地层的牙形石动物群 ,列出了牙形石的各个形态属种在地层中的分布及其数量变化。
3) Meishan section
煤山剖面
1.
From high resolution magnetostratigraphic study of the Meishan section of Changxing County, Zhejiang Province, the following conclusions are obtained: (1) The Meishan section can be divided into five normal polarity subzones and four reversed polarity subzones.
通过对浙江长兴煤山剖面的高分辨率磁性地层学研究，得出以下结论：（１）浙江长兴煤山剖面可划分为５个正向极性亚带和４个反向极性亚带。
2.
Based on detailed investigation of the sedimentology and conodont faunas on the Permian_Triassic boundary strata of the Meishan section, Zhejiang Province, South China, a new paleoecological model about two important genera Hindeodus and Clarkina (or Neogondolella ) is proposed.
通过对浙江长兴煤山剖面二叠－三叠系界线层沉积相分析及牙形石演化规律研究，提出了该时期Ｃｌａｒｋｉｎａ（Ｎｅｏｇｏｎｄｏｌｅｌａ），Ｈｉｎｄｅｏｄｕｓ两类重要牙形石属的生态新模式。
3.
The Dongling section can complement reptenished some deficiency of the Meishan section from its three features:ty.
ｐａｒｖｕｓ距界线粘土层顶面仅高出１３ｃｍ，化石保存完好以及界线粘土层至Ｐ／Ｔ界线附近均为单一的灰泥岩三特点弥补煤山剖面之不足。
4) Dameigou Formation
大煤沟组
1.
On the basis of integrated well data and seismic data,combined with the high resolution sequence stratigraphic data,the river-lake delta sedimentary system of the Dameigou Formation in the Yuka Coal Field in the north margin of the Qaidam Basin,was divided into short-term,middle-term and long-term base-level cycles.
利用高分辨率层序地层学理论和技术方法,综合地震、测井、岩芯和煤质资料对柴达木盆地北缘鱼卡煤田中下侏罗统大煤沟组地层河湖三角洲沉积体系进行高分辨率层序地层学分析,从中识别出短期、中期、长期3个级别的基准面旋回层序,划分出向上"变深"非对称型、向上"变浅"非对称型及对称型3种短期基准面旋回基本结构类型。
5) Jilonggou section
吉隆沟剖面
6) Damugou section
达木沟剖面
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|