1) thinckness tolerance
厚差
1.
0065mm high quality aluminum foils with thinckness tolerance of ±0.
在实际生产中严格控制生产要素 ,对坯料质量、辊系参数、道次分配和操作参数进行优化 ,并配备技术水平较高的操作手 ,小批量地轧制出了厚差为±0 。
2) unequal thickness
差厚
1.
Analysis about formation and microstructure of laser-welding-tailored-blanks with unequal thickness of high strength steels;
高强度钢差厚板激光拼焊焊缝成形及组织分析
2.
The microstructure of welded seam on the ST14 steels and High Strength Steels(HSS) LWTBs was analyzed in this paper, as well as its influence on the LWTBs' formability, the welding property of LWTBs with unequal thickness was also discussed.
本文通过研究ST14钢和高强度钢激光拼焊板焊缝组织及其形成原因，探讨了差厚板激光拼焊的焊接性能及其成形性能，为激光拼焊板提高焊接质量，并在生产领域不断发展和应用，提供理论和技术支持。
3) multi-gauge
差厚
1.
Research on tensile instability of multi-gauge high strength steel laser tailor-welded blank;
差厚高强钢激光拼焊板拉伸失稳行为研究
2.
In order to predict when and where the rupture of multi-gauge high strength steel of laser tailor-welded blanks(LTWB) happens,new failure criteria are proposed based on the research of failure behavior.
为准确判断差厚高强钢激光拼焊板何时、何处发生破裂,在失效行为研究的基础上建立一种新的破裂判据。
4) Edge thickness deviation
边部厚差
5) thickness deviation
厚度偏差
1.
The effect of thickness deviation on the reflection spectra and phase shift of VCSELs has been analysed using optical transfer matrix method.
采用光学传输矩阵方法分析了厚度偏差对VCSEL的反射谱和反射相移产生的影响。
2.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill,rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a variety of roll length,plate width and rolling force is studied too.
针对由于轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析了轧辊承受载荷的分布情况,研究了宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
3.
For researching thickness deviation of wide heavy plate caused by bilateral stiffness difference of plate mill, rolling force distribution is analyzed by using the principle of forces and torques equilibrium and the effects of the stiffness difference of plate mill on plate thickness deviation under a varity of roll length, plate width and rolling force is studied too.
针对轧机两侧刚度差异引起的宽厚板两侧厚度偏差,采用力平衡和力矩平衡原理,分析轧辊承受载荷的分布情况,研究宽厚板两侧厚度偏差与轧辊长度、板宽、轧制力和轧机两侧刚度差异之间的规律。
6) wall thickness difference
壁厚差
1.
Influence of process parameters on spinning force and wall thickness difference of shear spinning;
工艺参数对剪切旋压旋压力和壁厚差的影响
2.
Discussion About Wall Thickness Tolerance and Wall Thickness Difference of Bushing;
小议衬套壁厚公差与壁厚差
3.
Trial-manufacture indicates: forging process of thrust cone is feasible;wall thickness difference value of the f.
通过生产试制及产品检测,获得了壁厚差在1。
补充资料：差差
1.犹参差。不齐貌。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条