1) gas flame spray
气体火焰喷涂
1.
This article gives a general description of the use of the gas flame spray process,and analyses its work principle as well as the way of spray and spraying materials to achieve quality coatings.
介绍了气体火焰喷涂的应用概况 ,分析了气体火焰喷涂的工作原理以及为获得高质量涂层的喷涂方法与喷涂材料 ,指出了建立具有聚合物、非晶体材料固相夹杂物的多组分混合涂层 ,提高功率及焰流、粉粒的速度是今后发展的方向。
2) flame-sprayed conductor
火焰喷涂导体
3) flame spraying
火焰喷涂
1.
Experimental study of wear resistance of nickel based WC composite coating prepared by flame spraying and remelting+;
火焰喷涂重熔Ni基WC复合涂层的耐磨性能试验研究
2.
Influence of spraying distance of ceramic soft wire flame spraying on properties of layer;
陶瓷软线材火焰喷涂距离对涂层性能的影响
3.
On the properties of nylon 1010/nanometer TiO_2 coatings by flame spraying;
火焰喷涂尼龙1010/纳米TiO_2复合涂层力学性能研究
4) flame spray
火焰喷涂
1.
TiC-TiB_2 multiphase ceramic coatings prepared by reactive flame spray;
TiC-TiB_2复相陶瓷涂层的反应火焰喷涂制备
2.
Polyamide 1010(PA1010)/nano-ZrO2 composite coating was prepared by flame sprayed.
利用火焰喷涂法制备了尼龙1010(PA1010)/n-ZrO2复合涂层,采用差示扫描量热法(DSC)对复合涂层的非等温结晶过程、熔融行为进行了分析。
3.
Polyamide12(PA12) and PA12/nano-SiO_2 composite coatings were prepared by flame spray.
采用火焰喷涂法制备了聚酰胺12/纳米SiO2(PA12/nano-SiO2)复合涂层,利用差示扫描量热法(DSC)对复合涂层的非等温结晶过程、熔融行为进行了分析。
5) flame spray coating
火焰喷涂
1.
Flame spray coating endothermic ceramic coating and its wear-resistant behaviour;
吸热陶瓷涂层的火焰喷涂及其耐磨行为
2.
The paper introduces the principle ,apparatus and technology of Plastics powder using flame spray coating,coating materials as PP, EVA resin,nylon, polyphenyl thioether, chlorinated polyether and so on and their corrosion resistance.
介绍了塑料粉末火焰喷涂的原理、装置及工艺,聚乙烯、EVA树脂、尼龙、聚苯硫醚、氯化聚醚等涂层材料,以及这些涂层材料的耐腐蚀性能。
6) high velocity oxyfuel spraying
氧燃气超音速火焰喷涂
1.
Comparing with the traditional high velocity oxygen-kerasense flame spraying, the development of the DZ9000E high velocity oxyfuel spraying is emphasizing on reduction of the cost of coatings and removability of in-situ application under various working conditions.
与氧煤油超音速火焰喷涂系统相比,DZ9000E型氧燃气超音速火焰喷涂系统的开发更侧重于降低涂层的成本以及适应不同工况中现场使用的可移动性。
补充资料：火焰喷涂
分子式：
CAS号：
性质： 将金属粉末或塑料粉末用火焰喷枪喷涂到物体表面的涂布方法。聚乙烯、尼龙、氟树脂和环氧树脂广泛采用。其过程是粉末材料与适当的助溶剂混合后，用压缩空气或惰性气体将其从贮料槽中吹出，在锥形火焰中被加热到熔融温度，并喷到经过净化处理及预热过的工件上，直至达到所需厚度为止。适用于现场施工。
CAS号：
性质： 将金属粉末或塑料粉末用火焰喷枪喷涂到物体表面的涂布方法。聚乙烯、尼龙、氟树脂和环氧树脂广泛采用。其过程是粉末材料与适当的助溶剂混合后，用压缩空气或惰性气体将其从贮料槽中吹出，在锥形火焰中被加热到熔融温度，并喷到经过净化处理及预热过的工件上，直至达到所需厚度为止。适用于现场施工。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条