1) microhardness
[,maikrəu'hɑ:dnis]
微硬度
1.
Effect of 5.25%NaOCl Irrigation on the Microhardness of Root Dentin with Two Different Types of Instrumentation;
5.25%NaOCl冲洗液在两种不同机械预备根管时对牙本质微硬度的影响
2.
Study on the effect of endodontic irrigation MTAD on enamel and dentin microhardness of human teeth;
MTAD根管冲洗液对牙本质、牙釉质微硬度影响的研究
3.
Effect of endodontic irrigation solutions on enamel and dentin microhardness of human teeth;
根管冲洗液对牙本质、牙釉质微硬度的影响
2) microhardness
[,maikrəu'hɑ:dnis]
显微硬度
1.
Effects of heat treatment on microstructure and microhardness of Mg-5wt%Sn alloy;
热处理对Mg-5wt%Sn合金组织与显微硬度的影响
2.
The influence of magnetron sputtering TiN films processing parameters on microhardness;
磁控溅射TiN薄膜工艺参数对显微硬度的影响
3.
Research on microhardness and microstructure of nanocrystalline Cu;
金属Cu纳米晶体的显微硬度及微结构研究
3) hardness
[英]['hɑ:dnis] [美]['hɑrdnɪs]
显微硬度
1.
The hardness of the coatings are studied by the Micro-sclerometer.
采用直流和脉冲电镀法制备Ni/纳米SiC复合镀层,用显微硬度计测试了镀层的硬度。
2.
The micro-hardness from the surface to center was also measured.
采用双层辉光等离子表面冶金技术对Ti2AlNbO相合金进行渗Cr处理,采用扫描电子显微镜、辉光放电光谱分析仪及X射线衍射仪分析了渗Cr层的微观组织、化学成分及相组成,由表及里测试了渗层显微硬度分布,通过无润滑条件下的球-盘式摩擦磨损试验研究了渗Cr处理对其摩擦磨损性能的影响。
3.
The results showed that the hardness, bonding strength and friction coefficient of coatings were decreased with the increase of content of MoS2.
结果表明:随着自润滑材料MoS2含量的增加,涂层的显微硬度、结合强度和滑动摩擦因数都明显降低;当MoS2含量由6%增加到9%时,涂层滑动摩擦因数由0。
4) microstructure hardness
显微硬度
1.
The laser remelted technic can improve the microstructure hardness and thermal shock properties of the coatings.
分析了激光重熔过程对Al2O3-13ωt%TiO2陶瓷涂层的物相结构变化、显微硬度和抗热震性能影响。
2.
The components, microstructure, microstructure hardness, and the wear resistance of the alloy layers were tested.
采用2kW的CO2激光束在A3钢表面制备高硬质W C-T iN-Co合金熔覆层,并对不同扫描速度下合金层的成分、显微组织、显微硬度及耐磨损等性能进行了分析。
3.
This paper, through vanadatizing experiment of borate bath, obserVed the metallognphic strUcture and analyzed the microstructure hardness, and exploded the factors that influence the vanadatizing layers and its technology features, we apply this teChnology to the tools and dies of bearings, their longevity improved more than 5 than, achieving better results.
本文通过硼砂盐浴渗钒试验，对渗钒后的金相组织、显微硬度进行观测分析，对影响渗钒层的因素及其工艺特点进行分析探讨，并将此工艺应用于轴承的工模具，寿命提高五倍以上，取得较好的效果。
5) micro hardness
显微硬度
1.
Research on measuring software system of material micro hardness based on serial communication;
基于串口通信的材料显微硬度测量软件的研究
2.
Study on micro hardness of sintered ore of WISCO
武钢烧结矿显微硬度的研究
3.
Influence of processing parameters on micro hardness of 65 Mn steel was investigated systematically.
目的研究激光强化工艺参数对65 Mn旋耕刀基体显微硬度的影响,以表面硬度和磨损量为表征参数,寻求最佳工艺参数。
6) microhardness
[,maikrəu'hɑ:dnis]
微观硬度
1.
The distribution of cladding layer microhardness and its cause are studied as well as the enhancement of the surface wear resistance and the variation of the microstructures.
利用不同的激光工艺参数对Cr12 MoV模具钢表面进行熔覆试验 ,探讨了工艺参数对熔覆层深度的影响 ,研究了表面微观硬度的趋势及其原因、熔覆层耐磨性能的提高幅度以及组织结构的变化。
补充资料：微型硬度
分子式：
CAS号：
性质：由微型硬度计所测得的硬度，与标准硬度计相比，微型硬度计所用的压头和压入力均比标准硬度计小，因而既可以在标准试样上测量，也可以在采用标准硬度计不能测量的较小尺寸或较薄非标试样上进行测量。
CAS号：
性质：由微型硬度计所测得的硬度，与标准硬度计相比，微型硬度计所用的压头和压入力均比标准硬度计小，因而既可以在标准试样上测量，也可以在采用标准硬度计不能测量的较小尺寸或较薄非标试样上进行测量。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条