1) dot point glajing structures
点式玻璃幕结构
3) structural glass curtain walls
结构玻璃幕墙
4) point-supported glass curtain wall
点支式玻璃幕墙
1.
Due to its features of open-eyesight and good-perspective,the point-supported glass curtain wall system is popularly applied in public buildings,but it also has the flaw of high energy-consuming.
在公共建筑中广泛应用的点支式玻璃幕墙体系,具有视野开阔、通透美观的优点,但也有能耗过大的缺点。
2.
Point-supported glass curtain wall is a new kind of curtain wall and developing quickly, and it was applied in engineering recently.
点支式玻璃幕墙是近年来开始在玻璃幕墙工程中应用并迅速发展的一种新的幕墙型式。
3.
As a new kind of supporting member,a prestressed fish-shaped cable truss has been widely applied in point-supported glass curtain walls.
预应力鱼腹式索桁架作为点支式玻璃幕墙的支承体系有着广泛的应用,非线性自振特性的研究对于索桁架结构在地震荷载作用下的响应分析具有十分重要的意义。
5) point supported glass curtain wall
点式玻璃幕墙
1.
Installation technology of point supported glass curtain wall back cable system in Nanjing railway station;
南京火车站点式玻璃幕墙拉索体系安装技术
2.
This article mostly introduces the emphasis of large point supported glass curtain wall design and construction process by analyzing large point supported glass curtain wall of Foshan Electric Power Attempering Building.
本文以佛山电力调度大楼中的点式玻璃幕墙为例,重点介绍了该点式玻璃幕墙的设计要点及施工过程,对类似的工程设计和施工有一定的参考价值。
6) point-supporting glass curtain
点支式玻璃幕墙
1.
Static performance of single-layer cable Mesh point-supporting glass curtain;
单层索网点支式玻璃幕墙的静力性能研究
2.
Study of model-frequency behavior of single-layer orthogonal cable mesh point-supporting glass curtain;
单层正交索网点支式玻璃幕墙自振特性研究
3.
The connection types of supporting point of point-supporting glass curtain often adopt countersunk type or floating-head type.
在本文中,风荷载对点支式玻璃幕墙承载性能的影响,就分别按大挠度和小挠度进行分析和比较,提出了按大、小挠度理论计算的临界风荷载值。
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条